Peg-Perego Navetta XL Instrucciones De Uso página 12

mechanisms are connected properly.
• Do not insert fingers into the mechanisms.
• Do not use near heat sources, open flames or dangerous
objects that are within reach of the child.
• It could be dangerous to use accessories which are not
approved by the manufacturer.
• Make sure the belts fastening the Navetta XL to the vehicle
are always taut and adjust the straps securing the child.
• Never twist the belts.
• Replace the item if it undergoes significant strain in an
accident or shows clear signs of breakage or deformation.
• The safety device should not be modified by users in any
circumstances.
• Carefully follow the instructions supplied by the
manufacturer of the child restraint system.
• Never leave the child unattended in the Navetta XL in a vehicle.
• The Navetta XL must always be secured with the vehicle's
safety belts, even when the child is not present. In the event
of sudden braking, it could injure the occupants of the vehicle.
• When travelling in vehicles, never hold the child in your
arms and never put him/her anywhere but in the Navetta
XL. In the event of sudden braking, even at low speeds, the
child would be flung forward.
• Take particular care to make sure that luggage or other
objects are not located where they may injure the child in
the Navetta XL in the event of an accident.
• Do not leave the Navetta XL in vehicles exposed to the sun.
Some parts might heat up and be harmful to the delicate
skin of the child – check before placing the child in the seat.
• Make sure that the Navetta XL is not obstructed by any
moving parts of the vehicle's seat or by one of the doors.
• Do not use the Navetta XL without its fabric covering,
which cannot be replaced with one not approved by the
manufacturer since it is an integral part of the Navetta XL and
the safety system. If replacing it, use an official spare part.
• The design of the Navetta XL features a polystyrene shock
absorption device built directly into the shell, below the
padding: do not remove it.
• This product is only suitable for children who are unable to
sit up by themselves.
• This product is designed for children from birth up to a
weight of 9 kg. When used in vehicles it is designed for
weights of up to 10 kg.
• During use in vehicles, always fasten the safety harness.
When using the product as a carriage, remove the harness
and place it in the special pocket.
• Only use the product on surfaces that are hard, horizontal
and dry.
• Do not leave other children playing unattended near the carriage.
• Take care when adjusting the mechanisms (handle,
backrest) with the child present.
• Regularly check the handle (or the handles) and the
bottom of the carriage to make sure that there are no signs
of breakage or damage.
• When using the carriage with a stand, check the maximum
length of the carriage specified on the stand.
• The pram is intended for transportation purposes and
should not replace the cot at home.
• Do not use this product after 7 years from the date of
production indicated on the structure. The natural ageing
of the materials may mean that it is no longer compliant
with standards.
Instructions for use
Using the Navetta XL
1• HOOD: To attach the hood, fasten the clips (fig_a) and then the
buttons on the sides (fig_b) and, if present, the back (fig_c).
2• The hood comes with an insert which enables parents
to see the baby from all positions; NAVETTA XL in the
EMBOSSED FABRIC COLLECTION is excluded.
3• COVER: Put the cover in place and button it on both sides.
4• The cover can have different features, depending on
the collection.
If Velcro straps are present, the cover may be fastened to
the canopy, protecting the child more effectively against
bad weather. Unfasten the cover sides (arrow_a), pull the
flap upwards (arrow_b) and use the Velcro straps to fasten
this to the canopy (arrow_c).
5• Alternatively, there may be a button on the sides, as shown
in the figure.
6• HANDLE: Rotate the handle upwards until it clicks into
place (arrow_a). The handle is only locked in place when
it is in the vertical position. To lower the handle, press the
two round buttons at the same time (arrow_b) and rotate it
12