Specific Safety Instructions; Initial Operation - REMS E-PUSH Instrucciones De Uso

eng
D) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired.
c) Disconnect the plug from the power source before making any adjust-
ments, changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow per-
sons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tools operation. If damaged, have the power tool repaired by a
qualified expert or by an authorised REMS after-sales service facility
before use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Secure the workpiece. Use clamps or a vice to hold the workpiece. This
is safer than holding it with your hand, and also it frees both hands to ope-
rate the equipment.
h) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type
of power tool, taking into account the working conditions and the work
to be performed. Use of the power tool for operations different from those
intended could result in a hazardous situation. All unauthorised modifica-
tions to the power tool are prohibited for safety reasons.
E) Battery tool use and care
a) Ensure the switch is in the off position before inserting battery pack.
Inserting the battery pack into power tools that have the switch on invites
accidents.
b) Recharge only with the charger specified by the manufacturer. A char-
ger that is suitable for one type of battery may create a risk of fire when used
with another battery pack.
c) Use battery tools only with specifically designated battery packs. Use
of any other battery packs may create a risk of injury and fire.
d) When battery pack is not in use, keep it away from other metal objects
like paper clips, coins, keys, nails, screws, or other small metal objects
that can make a connection from one terminal to another. Shorting the
battery terminals may cause bums or a fire.
e) Under abusive conditions, liquid may be ejected from the battery, avoid
contact. If contact accidentally occurs, flush with water. If liquid con-
tacts eyes, additionally seek medical help. Liquid ejected from the
battery may cause irritation or bums.
f) Do not use the battery/charger at battery/charger temperatures or
ambient temperatures of 5°C/40°F or 40°C/105°F.
g) Do not dispose defective batteries in the normal domestic waste. Take
them to an authorised REMS after-sales service facility or to a reputed
waste disposal company.
F) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained.
b) Comply with maintenance instructions and instructions on tool
replacements.
c) Check mains lead of power tool regularly and have it replaced by a
qualified expert or an authorised REMS after-sales service facility in
case of damage. Check extension cable regularly and replace it when
damaged.

Specific Safety Instructions

• Wear your personal protective equipment (e. g., your eye protectors).
• Before every using of the machine, examine the high-pressure-hose for
damages.
• The electric pressure-testing pump develops a very high pressure. There-
fore, be particularly careful. When working with the electric pressure-testing
pump, keep out all the persons normally not being employed in this wor-
king area.
• When operating, the electric pressure-testing pump must stand in an hori-
zontal position and be in a dry condition.
• Do not switch-in the electric pressure-testing pump when the „Press" pres-
sure-regulating valve is closed. And do not operate the pressure-testing
pump for a longer period of time as well. Otherwise, the pressure-testing
pump will get overheated.
• Do not direct any liquid jets onto the electric pressure-testing pump. When
cleaning it, adhere to the same requirement as well.
• Do not pump any combustible fluids, acid solutions, or dissolvents.
• Protect electric pressure-testing pump against frost. If necessary, let run idle
for approx. 1 min so that the remaining water runs out or suck glycol/water
mixture.
• Before starting any servicing work, draw out the mains plug, and make un-
pressurerized the pressure-testing pump. Before dismounting the pressu-
re vessel, make it unpressurerized. Otherwise, when dismounting, the re-
maining pressure can catapult pieces out of the unit.
1. Specifications
1.1. Article No.
Electric pressure-testing pump
Connecting piece together with both the
manometer (60 bar/6 MPa/870 psi) and stop valve
Manometer with a microindication (16 bar/1,6 MPa/230 psi)
1.2. Application area
Leak testing to sanitary and heating facilities.
Pumping water or hydrous solutions, emulisions (not for continuous
operation)
pH-rating of fluids
Viscosity of fluids
Temperature of fluids
Maximum pressure
Maximum pumping capacity
Suction hose
High-pressure hose
Manometer (60 bar/6 MPa/870 psi), dampened by a filling
with glycerine
1.3. Electric specifications
Voltage
Frequency
Current consumption
Power
Speed of rotation
Protective system
Duty classification
1.4. Dimensions
1.5. Weight
1.6. Noise-immission information
Immission value referring to the workplace

2. Initial operation

2.1. Electric connection
Care must be taken to the power-line voltage! Before connecting the
pressure-testing pump, you must check and make sure that the electric
voltage indicated on the nameplate complies with the line / mains volta-
ge supplied by the power station. Put the (1) switch into the „0" position.
When employing an extension cable, make sure that the required cross-
sectional area ( 1,5 mm 2 ) will be used. If working in an humid environ-
ment, then it will be required that the pressure-testing pump is operated
via a 30-mA current-operated earth-leakage circuit breaker.
2.2. Suction hose
Fasten the (2) suction hose by means of screws at the (3) connecting
piece. Do not kink the suction hose. Pump clean fluids only. Do not re-
move the (4) suction filter at the suction hose. Make sure that the pres-
sure-testing pump does not suck in any air. Otherwise, its function will be
affected.
2.3. High-pressure hose
Fasten the (5) high-pressure hose by means of screws at the (6) connec-
ting piece.
eng
115100
115110
115045
7 ... 12
1.5 mPa s
–30°C ... 60°C
60 bar (6 MPa/870 psi)
7 l/min
1 / "
2
1 / "
2
Grade 1.6
230 V 1~
50 Hz
7.5 A
1750 W
2800 1 /min
IP 25
S3 20%
450×200×300 mm
13 kg (29 lb)
83 dB(A)