Direct Code Entry; Code Search; Brand Search; Code Identification Feature - Philips SRU4105WM/17 Instrucciones Y Manual Del Propietario

Direct Code Entry

1. Press and hold SETUP until the indicator remains on,
then release SETUP.
2. Repeatedly press SELECT to select the desired
mode (TV, VCR, etc.), unless the desired mode is
already selected.
3. Enter the 4-digit code from the code tables (on
separate sheet). Note: After a valid code entry, the
indicator turns off. For an invalid code, the indicator
flashes.
4. Press CHANNEL UP. If the device responds, no further
programming is required. Note: If some buttons do not
operate your equipment, try one of the other codes for
your brand.

Code Search

If your product does not respond after you have tried all
the codes for your brand or if your brand is not listed,
try searching for your code by following these steps.
1. Turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold SETUP until the indicator remains
on, then release SETUP.
3. Repeatedly press SELECT to select the desired
mode (TV, VCR, etc.), unless the desired mode is
already selected.
4. Press CHANNEL UP repeatedly (up to 300 times)
until the device to be controlled changes channels.
The indicator blinks off with each button press.
5. Press and release MUTE to install the code.
Most users store VCR codes under VCR. Cable codes
appear under CBL (Cable), etc.
If you want to store a VCR code under CBL, first follow
the procedure for Direct Code Entry and select CBL in
Step 2 of Direct Code Entry. Then enter any VCR code in
Step 3 of Direct Code Entry. Then follow the steps above
for Code Search.
Note: If the device does not have a CHANNEL UP
button, use PLAY (VCR only) or POWER instead.
Code search begins from the currently stored 4-digit
number under that mode.
8
Code Search by Brand
Lets you search for a code for a specific Brand within
the Code Library for a particular manufacturer.
1. Turn on the device (TV, VCR, etc.) to be controlled.
2. Press and hold SETUP until the indicator remains on,
then release SETUP.
3. Repeatedly press SELECT to select the desired
mode (TV, VCR, etc.), unless the desired mode is
already selected.
4. Press and release the numeric button (0-9)
corresponding to desired Manufacturer (see table
on code list sheet). The green indicator blinks off
once. Note, pressing "0" performs a full library
search same as normal Code Search Method on
previous page.
5. Press the CHANNEL UP button ((or POWER or
PLAY (VCR only)) repeatedly until the device to be
controlled changes channel. The green indicator
blinks off with each button press. If you accidentally
overshoot the code required, press the CHANNEL
DOWN button to backtrack through the library until
the device changes channel. Pressing CHANNEL
UP changes direction to forward again.
6. Press and release MUTE to install the code.
Brand Search Method entry is now complete.
Note: When all codes under a Brand have been
searched the indicator flashes rapidly for 3 seconds.

Code Identification Feature

The Code Identification Feature lets you identify the 4-
digit library code stored under your device key.
If you want to find what 4-digit code is stored under any
device mode, follow these steps.
1. Press and hold SETUP until the indicator remains on,
then release SETUP.
2. Repeatedly press SELECT to select the desired
mode (TV, VCR, etc.), unless the desired mode is
already selected.
3. Press and release SETUP. The indicator blinks.
4. To find the first digit for the code stored under the
mode selected in Step 2, press each number button
(0-9). When the indicator blinks off, the number you
pressed is the first code digit you are searching for.
5. To find the second digit, repeat Step 4. When the
indicator blinks off, this is the second digit.
6. Repeat Step 4 to find the third and fourth digits.
9