Maintenance And Service; Working Advice - stayer 384B Manual De Instrucciones

Operation
Starting Operation
- Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified
on the nameplate of the machine. Power tools marked
with 230 Vcan also be operated with 220 V.
Reversing the Rotational Direction
The rotational direction switch 8 is used to reverse the
rotational direction of the machine.
However, this is not possible with the On/Off switch 7
actuated.
Right rotation: For driving in screws, push the rotational
direction switch 8 left to the stop.
Left rotation: Push the rotational direction switch 8 right
to the stop (for unscrewing screws).
Switching On and Off
To start the machine, press the On/Off switch 7 and keep
it depressed.
To lock the pressed On/Off switch 7, press the lock-on
button 6.
To switch off the machine, release the On/Off switch 7 or
when it is locked with the lock-on button 6, briefly press
the On/Off switch 7 and then release it.
Adjusting the Speed
The speed of the switched on power tool can be variably
adjusted, depending on how far the On/Off switch 7 is
pressed.
Light pressure on the On/Off switch 7 results in a low
rotational speed. Further pressure on the switch results in
an increase in speed.
Adjusting the Screw-in Depth
With the adjustment sleeve 3, the screw-in depth of the
screw head into the workpiece can be preset in 12 locking
steps per full turn. Each step corresponds with a 0.125
mm change of the screw-in depth.
Turning the adjustment sleeve 3 in clockwise direction
results in a greater screw-in depth; turning in anticlockwise
direction reduces the screwin depth.
The required setting is best determined by testing.

Working Advice

- Apply the power tool to the screw only when it is
switched off. Rotating tool inserts can slip off.
Guide the screw toward the screwdriving bit 1. The screw is
held in place by the magnet pull of the universal bit holder
9. Firmly push the tip of the screw into the material to be
screwed until the screwing-depth stop 4 faces against the
workpiece.
Switch the machine on. The screw is screwed into the
material until the adjusted screw-in depth is reached. The
drive is disengaged and the tool holder no longer rotates.
Check the screw-in depth and readjust, if required.
For unscrewing screws, set the rotational direction switch
8 to left rotation and pull off the screwing-depth stop 4
toward the front without turning the adjustment sleeve.
Working with the screwing-depth stop 4 is also possible
when adapting the screw-in depth.
m_384B_v8.indd 8
ENGLISH
8
Belt Clip
With the belt clip 5, the machine can be hung onto a belt.
The user has both hands free and the machine is always
at hand.

Maintenance and Service

Maintenance and Cleaning
- Before any work on the machine itself, pull the mains
plug.
- For safe and proper working, always keep the machine
and ventilation slots clean.
If the machine should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for Stayer
power tools.
WARNING! Important instructions for connecting a new
3-pin plug to the 2-wire cable. The wires in the cable are
coloured according to the following code:
Do not connect the blue or brown wire to the earth terminal
of the plug.
Important: If for any reason the moulded plug is removed
from the cable of this power tool, it must be disposed of
safely.
Disposal
The machine, accessories and packaging should be
sorted for environmental-friendly recycling.
Only for EC countries:
Do not dispose of power tools into
household waste!
According
2002/96/EC
and
implementation into national right, power
tools that are no longer usable must be
collected separately and disposed of in
an environmentally correct manner.
8
the European Guideline
for Waste Electrical
Electronic Equipment and its
16/02/2019 11:21:43