Nowsonic Roadtrip 508 Instrucciones De Uso página 5

ROADTRIP 508
GB
User manual
Description of the Inputs
Roadtrip 508 has 7 monophonic and one stereophonic input. The mono
channels have the following controls:
1
1) The VOLUME control adjusts the gain of the corresponding chan-
nel in the LEFT/MAIN and RIGHT MON outputs and therefore the
balance between the inputs. The signal of the channel is always
routed to both outputs.
2) The HIGH and LOW controls adjust the amount of high and low fre-
quencies on the particular input. The cutoff frequency for the HIGH
shelf filter is 12kHz, the LOW filter works from 80Hz, the control
range is +/- 12dB each.
3) The FX control feeds the channel signal to the internal multi effects
processor.
4) The MON VOL control feeds the channel signal to the RIGHT/MON
output if the AMP MODE MAIN/MON was chosen in the Master
section.
The Combo sockets in the lower part of the mixer panel serve as the
inputs for the channels 1 to 7. Via the Combo sockets you can input
the following sources to the channels:
Channel Source
1 Device for audio playback
via Bluetooth, micropho-
ne or line signal
2 – 4 Microphone or line signal
5 – 7 Microphone, line signal
or instrument
Channel 1 is equipped with a Bluetooth receiver for wireless reception
of audio data from any external devices like laptops and smartphones.
You can toggle between Bluetooth and the Mic/Line socket via the
button of the same name above the VOLUME control of channel 1.
The communication between Roadtrip 508 and the external Blue-
tooth device is configured via the BLUETOOTH CONTROLLER panel. In
addition, you can control the transport of the device here. The panel
provides the following controls and indicators:
2 3 4
Connector
Internal Bluetooth receiver, XLR or
TRS jack via Combo socket
Combo socket, XLR or TRS jack
Combo socket, XLR or TRS jack
In order to receive the Bluetooth signal, you must first set up the con-
nection between Roadtrip 508 and the external device via the BLUE-
TOOTH CONTROLLER panel. Proceed as follows:
1) Place the external Bluetooth-enabled device next to Roadtrip 508
(<10m).
2) Press and hold the PLAY/PAUSE button
10 seconds
3) 3. Release the button, when you hear two beeps from Roadtrip
508: Now, the external device can find Roadtrip 508 and pair with
it. As soon as the connection is established, the CONNECTED LED is
permanently lit. If the connection failed, the NOT CONNECTED LED
lights up: in this case repeat the process.
If you want to disconnect the Bluetooth device from Roadtrip 508 (for
example to pair Roadtrip with another Bluetooth device), press the
PLAY/PAUSE button for 3 seconds: After the next beep the connection
is terminated.
NOTE: Roadtrip 508 can only be paired with a single Bluetooth device
at the same time. The distance from the Bluetooth source must not
exceed 10 meters. If no connection can be established, reduce the
distance and try again.
If Roadtrip 508 is powered down and up again, you must not perform
a new scan to pair with the Bluetooth device: Press and hold the PLAY/
PAUSE button for about 3 seconds.
After the beep, the connection with the Bluetooth device is re-esta-
blished.
When Roadtrip 508 is paired with the Bluetooth device, you can con-
trol the transport via the BLUETOOTH CONTROL panel. The following
functions can be controlled:
The PLAY/PAUSE button starts and pauses audio playback.
The VOLUME + button increases the volume of the
external device.
The VOLUME - button decreases the volume of the
external device.
Pressing the SKIP BACK button once skips to the beginning of
the current song. Press and hold the button to scroll back to the
beginning of the song.
Pressing the SKIP FORWARD button once skips to the beginning
of the next song. Press and hold the button to scroll forward to
the end of the current song.
6
www.nowsonic.com
for about