Initial Use - Steinbach 049106 Manual De Instrucciones

EN
2) Unscrew the covers from the inlet and outlet. (Illustration 3)
3) Put the O ring onto both connector pieces and attach these
firmly to the inlet and outlet. (Illustration 5,6)
4) Close the water feed to the pool on the inlet nozzle. (Illus-
tration 7)
5) Ensure that all water bearing pipes are closed (illustration
8)
6) Remove the pipe between the filter pump and inlet nozzle.
Unscrew the connection directly at the inlet nozzle only. (Il-
lustration 9)
7) Connect this pipe to the solar collector only (Illustration 2
point A) and fasten this with a hose clip. (Illustration 10)
8) Attach the hose Ø 38 mm included to the outlet side of the
solar collector (illustrations 2 point B, and 11) and the other
end to your pool's inlet nozzle. (Illustration 12)
9) Turn the aluminium supporting poles to the vertical position,
and adjust the poles to the appropriate length. Hold the end
of aluminium pole, and turn it clockwise to lock the alumin-
ium pole.(Illustration 13, 13a, 13b)
10) Insert one split pin through each of the two holes in the feet
(figure 13c).
11) Remove the protective covering on the upper side of the
collector. (Illustration 14)
Connecting several collectors:
If you would like to increase the heating power, you can connect sev-
eral collectors together. (Illustration 15) For this you will need a addi-
tional swimming pool hose Ø 38 mm.
We recommend connecting a maximum of 2 collectors, depending on
the power of your filter unit.
We definitely recommend use of a bypass set (Item no. 060045))
(Illustration 16) Item No. 060045
Not only does this help optimal control of heat output, it also
helps targeted control of the water flow rate, depending on the
power of the filter unit.
5

Initial use

Once the solar collector is assembled and the hoses are connected
to the filter pump and the pool, open the water supply and ensure that
water is flowing through the hose. Then turn on the filter system. Air
bubbles will rise from the inlet nozzle in the pool. This happens as the
air is expelled from the solar collector. If this continues for more than
2-3 minutes, check the tightness of the connections in your system.
Please note: Cover your pool overnight to avoid loss of heat.
6 Trouble shooting
Problem Cause / Solution
The pool does not • Make sure that water is flowing through
warm up.
the hoses.
• Has it been sunny enough?
• Exploit the maximum amount of sunlight
and increase the running time of the filter
pump.
• Cover your pool overnight to avoid loss
of heat.
• It is possible that you may need several
solar collectors.
No bubbles appear af- • Check the filter system and ensure that
ter the equipment has
water from the pool is flowing through
been attached to the the filter pump, then through the solar
pump.
collector and finally through the con-
nector hose back to the pool.
Steinbach Solar Collector Exclusive | 2019_V1
Air bubbles come out • Check the connector hoses for any dam-
of the pool return after
age.
the pump has been
• Check that the hose clamps have been
turned on.
properly tightened.
Water escaping. • Check the seals in the system of pipes.
• Check whether you have tightened the
hose clamps tightly enough.
• Check the connector hoses for any
cracks.
7 Service
For technical information, if any parts are missing, or in the event of a
complaint, please contact our customer service department directly:
Steinbach Vertriebs gmbH
Aistinger Strasse 2, 4311 Schwertberg, Austria
https://service.steinbach.at
email: [email protected]
www.steinbach.at
Overview of spare parts:
= Art. Nr. 049959
= Art. Nr. 049915
= Art. Nr. 110262
= Art. Nr. 060039
= Art. Nr. 049956
Page 5 of 32