Biosonic UC125H Manual De Usuario página 3

4
the warranty. Do not place objects directly
on bottom of tank. Always use accessory
baskets, cassette racks or beakers.
IV. Degassing Instructions
Degassing the solution eliminates large air bubbles that interfere with the cleaning
process and is necessary each time new
solution is added to the tank.
1. PRESS THE DEGAS KEY.
2. WAIT. The UC125H will begin to
cycle on and off during the degassing
process. The timer will count down
from five minutes. The words "Degas
On" will be displayed.
3. DEGAS COMPLETE! Once the
timer reaches zero, the words "Degas
Complete" will be displayed. Your
solution is now ready for use.
Pressing any key will take the user
back to the main screen.
V. Operation Instructions
ACTIVATING THE UC125H. This section
explains how to clean instruments with
your BioSonic UC125H.
1. Press the ENTER key.
2. SELECT A LOAD. Three load icons
will appear representing instrument
baskets, beakers and cassettes. To
cycle through these icons:
a. PRESS THE ENTER KEY
to choose the appropriate icon for
your particular load. The selected
icon will flash; push ENTER key
again to move to another icon.
b. If necessary, USE THE ARROW
KEYS to increase or decrease the
amount of cleaning time required per
load (between 5 and 60 minutes).
PRESS THE ENTER KEY again to
store the newly programmed default
times.
c. PRESS THE STOP/START KEY to
begin cleaning.
3. WAIT. The UC125H will begin the
cleaning process. The UC125H will
continue to clean as the timer counts
down the remaining minutes from the
user-selected cleaning time. You may
increase or decrease the cycle time
during operation by pressing the
ARROW keys up or down. Once the
timer reaches zero, "Cycle Complete"
will display on the LCD screen until
any button is pressed. The LCD will
then return to the main screen.
NOTE: The cleaning cycle can be
stopped at any time by pressing the
STOP/START button. The unit will then
return to the main screen. Pushing the
STOP/START KEY from the main LCD
screen will start the last cycle time
selected. To change the required cycle
time, go back to step 2.
C-POWER: C-Power is an exclusive feature of the UC125H that will
automatically adjust the power in the tank
based on the load requirements. This
function provides improved stability
against varying solutions, solution level
and instrument loads.
The BioSonic Ultrasonic cleaner should
always be covered when operating to trap
aerosols in the unit. The BioSonic
UC125H is equipped with a "hinged"
cover for easy one hand opening. The
cover also conveniently lifts off for
cleaning in spaces with low cabinets
above the unit.
VI. Heater Operation Instructions
ACTIVATING THE HEAT FEATURE. The
UC125H model is equipped with a heater
to rapidly increase the temperature of the
solution in the tank.
NOTE: The temperature in the tank is
displayed in the lower right-hand corner of
the LCD screen.
1. PRESS THE HEAT KEY. Pressing
the HEAT key to activate this feature
will bring up a new screen on the
display. The first time this feature is
activated, the user must choose to
use Celsius or Fahrenheit. Using the
Arrow Keys, select "C" for Celsius or
"F" for Fahrenheit and press ENTER.
2. SET THE DESIRED
TEMPERATURE. Use the Arrow
Keys to increase or decrease
the tank temperature between
25°C (75°F) up to 60°C (140°F) in
5° degree increments. Press START
to accept this temperature. The unit
will now begin to heat.
3. WAIT. The UC125H will now display
the default screen and begin to heat
to the desired temperature. The Heat
Toggle will now display "ON." Once
the desired temperature is reached,
the Heat Toggle will display "OK."
Current temperature information will
BioSonic
always be displayed in the lower
right-hand corner of the LCD display.
CAUTION: The Heat feature of the
UC125H is a pre-heat temperature only.
Through prolonged use, the natural
cavitation process will continue to heat
the solution beyond the desired
temperature. When this happens, the unit
is still functioning properly.
NOTE: Once the unit is programmed to
use either Celsius or Fahrenheit, it will not
prompt you to do this again. If a mistake
is made or the user desires to change
from one to the other option, after
entering heat mode, press and hold the
HEAT key for three seconds and then
repeat steps 1 through 3.
VII. Solution Reset Operation
Instructions
USING THE SOLUTION TIMER. The
UC125H is equipped with a Solution
Reset button. This feature tracks the
amount of time your solution has been in
use. The solution life is displayed in hours
and minutes immediately above the
SOLUTION RESET key. To utilize
this feature:
1. PRESS THE SOLUTION RESET
KEY once after every change of your
ultrasonic cleaning solution. It is
recommended to change your
solution every 8 hours at a minimum,
or whenever the solution becomes
visibly cloudy or soiled.
Coltène/Whaledent offers a variety of
BioSonic ultrasonic cleaning solutions
to meet your cleaning needs.
2. VERIFY. The solution timer should
now display zeroes in the lower-left
corner of the LCD display.
VIII. Cleaning Methods
A. In Tank
Basket Cleaning: Place parts to be
cleaned into the basket (Fig. 5, 6, 7).
Then place the basket directly into the
main tank containing BioSonic
General Purpose, Germicidal, or
Enzymatic Cleaner. Clean according
to instructions on bottle cleaner label.
B. In Beaker
For specialized item cleaning (e.g.,
prostheses): Place item into a beaker
(Fig. 11), add desired cleaning solution
(e.g., BioSonic Cement Remover or
BioSonic Ammoniated General
®
UC125H