Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Review this chart to find do-it-yourself
solutions
for minor performance
problems° Any ser-
vice needed,
other than those described
in this owner's manual,
should
be performed
by
an authorized
service
representative°
I
Cleaner won't start°
Poor job of dirt
ptck-up.
Cleanerstarts but
cuts off.
1. Unpluggedat wall outlet
2, Trippedcircuitbreakedblownfuse
at household servicepanel
3. Loose hose electrical connections
4_ Trippedoverload protector in
POWER-MATE
TM
1. Ful!or clogged dust bag
2o Clogged aidlow passages
3, Dirty molar safety filter
4, Wrong pileheight setting
1. PIug In firmly,push ONIOFF switch to ON
2, Reset circuit breaker or replace fuse
5_
6o
7,
8,
9, Dirty brush or brush supports
10. Cantsterhood open
I., Hoseorhoodelectrical
connections,
2- Tripped overloadprotector in
POWER.MATE
TM
3. Tripped overload protector
in canisle[
3. Reconnecthose ends, (page7)
4o Clean brush and brush supports,
then reset, (pages 14, 15)
1o Change bag, (page 12)
2, Clear airflow passages,(page 12)
3o Clean filter, (page 13).
4. Adjust selling, (page 9}
Adjust control, [page 11)
Replace hose
Change brushes, (page 16)
See BELT CHANGING AND BRUSH
CLEANING, (pages 14, 15)
10. Close and lalch hood,
1. Check connections, reconnecl hose
ends, (page 7)
2, Removeany items lhat may be caught
or jammed, lhen reset If cleaner starts
and stops again, clean brush and brush
supports, then reset, (pages 14, 15)
3. Change dust bag, clear aidlow blockage,
(page 12). Wait 20 minutes for motor
to cool and automalicaflyresel
I. Plug in firmly, (page 6).
2 & 3. See BELT CHANGING AND BRUSH
CLEANING, (pages t4, 15)
4_ Check brush area for excessive lint
buiId-upor jammingClean brush and
brush supports, then reset, (pages 14, 15)
1. Change bag, (page 12)
2. Change filter, (page 13).
3_ Clear clogfrom airflowpassage, (page 12)
4, This is normal, Light should go off
when tool is removed
Open suctioncontrol
5.
Hole in hose
6.
Worn POWER-MATE
TM
brushes
7.
Worn or broken belt
8 & 9.
i
....
•
POWER-MATE
TM
will not
to POWER-MATE
TM
conneclions
run when attached,
unpiugged
2o Worn or broken belt
3. Dirtybrush or brush supports.
4. Tripped overload proteclor in
POWER-MATE
TM
Performance indicator,
1o FuIl or clogged dust bag
some models, Is red,
2. Dirty filter,
3. Clogged airflow passage
4. Certain attachment tools
Cleaner picks up moveable
I_ Wrong pile height setting
1. Adjust setting, (page 9)
rugs -or- POWER-MATE
TM
2. Suclion too strong
2, Open suction control, (page I1)
pushes too hard.
Light won't work°
1.. Burned out light bulb
1. Change lightbulb, (page 14)
Cord won't rewind°
I. Dirty power cord
1. Clean the power cord
2. Cord jammed
2. Pull out cordand rewind
Cleaner leaves marks
1o Wrong vacuuming paltern.
1. SeeVACUUMINGTIPS, (page 9}
on carpet,
17
Tabla de contenido
