Starting Charge/Discharge Processes With; Bid Chip/Key; Reading Out The Data On A Bid Chip; Usb Pc Socket - Multiplex Power Peak E7 EQ-BID Instrucciones De Uso

saved to the BID chip or key: navigate to the "Store" line, and press
the "START / ENT." button to save the data.
If the BID chip or key has already been operated with another char-
ger, the data are naturally adopted. However, if the set parameters
are not compatible with the E7 charger (charge / discharge current,
cell count, capacity), an error message appears, and you have to re-
enter the data.
16.1 STARTING CHARGE / DISCHARGE PROCESSES WITH
BID CHIP / KEY
When you have edited and saved the BID data, the "BID EDIT"
screen display appears. Processes are initiated from this display.
This is accomplished by holding the "START / ENT." button
pressed in for at least two seconds. The various modes (CHARGE,
DISCHARGE, STORAGE, FAST-CHARGE, BALANCE, etc.) are
then displayed.
The procedure is identical to that required for starting a process for
one of the twenty memories ("Memory name" menu). The same
set-up facilities and parameters are available.
After highlighting the desired process using the "+" or "-" but-
tons, hold the "START / ENT." button pressed in for at least two
seconds to start.

16.2 READING OUT THE DATA ON A BID CHIP

If you wish to read out the saved data, you must first press the
"STOP / ESC" button. This display now shows the maximum
charged-in and discharged capacity of all the charge / discharge
processes involving this battery.
Note:
The data cannot be displayed if any process (charging, dischar-
ging, etc.) is currently active.
The illustration shows a typical screen display, which gives you a
means of estimating the values for your battery, and accurately
assessing the overall state of the pack . No additional equipment,
such as a PC with the appropriate software, is required.
BID Info
LiPo 11.1 V 4000 mAh
Last ChgCapa :
Max ChgCapa :
Num ChgCycles:
Last dChgCaps:
Max dChgCaps:
An analysis of the example display shows the following:
• To date the battery has been charged twice with the charger,
terminating with the "END" message.
• The highest charged-in capacity was 1100 mAh. At the
moment a capacity of 1000 mAh has been charged in.
• The highest discharged capacity was 600 mAh. At the moment
a capacity of 500 mAh has been discharged.
Operating Instructions
Power Peak E7 EQ-BID
®
1000 mAh
1100 mAh
2
500 mAh
600 mAh
28
14

17. USB PC SOCKET

The Power Peak ® E7 EQ-BID is fitted with a mini-USB socket at the
front. A USB lead can be connected to either of these sockets for
connection to a PC. The appropriate lead can be obtained from any
electronics shop. Software updates can be loaded using this lead.
USB charge socket
The charger is fitted with a 5 V / 2.1 A USB charge socket on the
front. This can be used for charging smart-phones and digital cam-
eras.

1 . ERROR MESSAGES

8
The Power Peak E7 EQ-BID is equipped with special safety fea-
®
tures to ensure safe and reliable charging and discharging operati-
ons. As soon as a fault occurs, a corresponding message appears
on the screen, and the piezo buzzer emits a warning tone. After
eliminating the cause, you can erase the following error messages
by pressing the "STOP / ESC" button.
[ Error ]
DC input too low
* Please check the
Input voltage!
[ Error ]
Interruption
* The battery
is disconnected.
* Please connect the battery
and start.
[ Error ]
Reverse polarity
* The battery is connected to
the output with reversed
polarity!
[ Error ]
Balance lead error
* Connect the
balance lead.
[ Error ]
Connection error
* The battery was disconnected
during an active process.
* Possible short-circuit
at the output.
# 30 8127
[ Error ]
DC input too high
* Please check the
Input voltage!
[ Error ]
No battery
* No battery is
connected to the output.
[ Error ]
Capacity limit
* The set capacity
limit has been reached.
[ Error ]
Cell count incorrect
* Incorrect number of cells set
[ Error ]
Cell error
* Voltage of one battery cell is
too low.