Starting Charge / Discharge Processes With A Bid Chip Or Key; Charge Output 2; Usb Pc Socket; Error Messages - Multiplex Power Peak D7 EQ-BID Manual De Uso

saved to the BID chip or key: navigate to the "Store" line, and press
the "START / ENT." button to save the data.
If the BID chip or key has already been operated with another char-
ger, the data are naturally adopted. However, if the set parameters
are not compatible with the D7 charger (charge / discharge current,
cell count, capacity or "Special" battery with the Power Peak E1), an
error message appears, and you have to re-enter the data.
16.1 StartING CHarGE / DISCHarGE PrOCESSES wItH
BID CHIP / kEy
When you have edited and saved the BID data, the "BID EDIT"
screen display appears. Processes are initiated from this display.
This is accomplished by holding the "START / ENT." button
pressed in for at least two seconds. The various modes (CHARGE,
DISCHARGE, STORAGE, FAST-CHARGE, BALANCE, etc.) are
then displayed.
The procedure is identical to that required for starting a process for
one of the twenty memories ("Memory name" menu). The same
set-up facilities and parameters are available.
After highlighting the desired process using the "+" or "-" but-
tons, hold the "START / ENT." button pressed in for at least two
seconds to start.
16.2 rEaDING OUt tHE Data ON a BID CHIP
If you wish to read out the saved data, you must first press the
"STOP / ESC" button. This display now shows the maximum
charged-in and discharged capacity of all the charge / discharge
processes involving this battery.
Note:
The data cannot be displayed if any process (charging, dischar-
ging, etc.) is currently active.
The illustration shows a typical screen display, which gives you a
means of estimating the values for your battery, and accurately
assessing the overall state of the pack . No additional equipment,
such as a PC with the appropriate software, is required.
LiPo 11.1 V 4000 mAh
Last ChgCapa :
Max ChgCapa :
Num ChgCycles:
Last dChgCaps:
Max dChgCaps:
An analysis of the example display shows the following:
• To date the battery has been charged twice with the charger,
terminating with the "END" message.
• The highest charged-in capacity was 1100 mAh. At the
moment a capacity of 1000 mAh has been charged in.
• The highest discharged capacity was 600 mAh. At the moment
a capacity of 500 mAh has been discharged.
Operating Instructions
Power Peak
BID Info
1000 mAh
1100 mAh
2
500 mAh
600 mAh
D7 EQ-BID
®
17. CHarGE OUtPUt 2 / OUt2
The Power Peak D7 EQ-BID charger is fitted with a second charge
®
output, which has the same specification as Output 1. Both charge
outputs can be operated independently of each other.
Note:
Do not wire the outputs together in parallel or in series!

18. USB PC SOCkEt

The Power Peak D7 EQ-BID is fitted with two mini-USB sockets
®
at the front. A USB lead can be connected to either of these sok-
kets for connection to a PC. The appropriate lead can be obtained
from any electronics shop. Software updates can be loaded using
this lead.
USB charge socket
The charger is fitted with a 5 V / 1 A USB charge socket on the
front. This can be used for charging smart-phones and digital
cameras.

19. ErrOr MESSaGES

The Power Peak ® D7 EQ-BID is equipped with special safety fea-
tures to ensure safe and reliable charging and discharging operati-
ons. As soon as a fault occurs, a corresponding message appears
on the screen, and the piezo buzzer emits a warning tone. After
eliminating the cause, you can erase the following error messages
by pressing the "STOP / ESC" button.
[ Error ]
DC input too low
* Please check the
Input voltage!
[ Error ]
Interruption
* The battery
is disconnected.
* Please connect the battery
and start.
[ ]
Error
Reverse polarity
* The battery is connected to
the output with reversed
polarity!
[ Error ]
Balance lead error
* Connect the
balance lead.
[ Error ]
Connection error
* The battery was disconnected
during an active process.
* Possible short-circuit
at the output.
14
Order No.
8129
[ Error ]
DC input too high
* Please check the
Input voltage!
[ Error ]
No battery
* No battery is
connected to the output.
[ Error ]
Capacity limit
* The set capacity
limit has been reached.
[ Error ]
Cell count incorrect
* Incorrect number of cells set
[ Error ]
Cell error
* Voltage of one battery cell is
too low.