Replacement Of Spool; Trouble Shooting; Storing; Guarantee - Echo EGT-350 Instrucciones De Manejo

10. Replacement of spool

First, switch off and unplug the device. Wait until the nylon thread has
come to a halt.
15
1
16

11. Trouble shooting

• Trimmer does not work: Check power supply (e.g. by testing on an-
other socket or by means of a voltage tester). Should it still not work,
although the socket is o.k., send it undissected to an authorised service
station for repair.
• Cutting line disappears into spool: Remove spool, pull end of line
through the metal outlet and reinsert spool. In case nylon line is used
up insert a new spool with line.
Do not make any other repairs on your own; have your trimmer
checked and repaired by an authorised dealer.

12. Storing

Always withdraw the plug when carrying out maintenance and servicing.
• Clean the unit thoroughly, especially the cooling air slots on the motor
housing.
• Do not use water to clean the device.
• Store trimmer indoors in a dry, high or locked place and keep out of
reach of children.

13. Guarantee

In the case of a claim for guarantee or defects, please contact the place
of purchase.

14. Waste disposal and environmental protection

Dispose of the machine properly after it is worn out. Disconnect the
mains cable in order to prevent misuse. Do not dispose of the machine
with the household waste. In the interest of environmental protection,
take it to a collection point for electric machines. Your responsible local
authority can provide you with addresses and operating times. Also take
the packaging materials and worn out accessories to the appropriate
collection points.
Only for EU countries
Do not discard electric tools in the household waste!
In accordance with European Directive 2012/19/EC on waste electrical
and electronic equipment and its implementation in national law, waste
electric tools must be collected separately for environmentally-compat-
ible re-use.
Recycling alternative to the return invitation:
Instead of returning the electric equipment, the owner is alternatively ob-
GB | Operating Instructions
Then push the two locking de-
vices 1 at the sides of the cutting
head, and remove the cutting
head cover 2 (fig. 15).
1
Remove the used thread coil and
2
put in the new coil 3 such, that
one end of the thread comes
out of each outlet at the sides of
the cutting head (fig. 16). Please
take care that the spring 4 is
3
properly seated under the thread
coil. Finally, close the cover by
4
pushing it in its seat. Both locks
must properly engage.
1
ligated to take part in the proper recycling in the case of relinquishment
of ownership. The waste equipment can also be taken to a collection
facility which disposes of it in the sense of the national recycling man-
agement and waste acts. This does not pertain to the accessory parts
and auxiliary equipment without electrical components accompanying
the waste equipment.

15. Spare parts

If you need accessories or spare parts, please contact our Service de-
partment.
When working with this tool, do not use any accessory parts other than
those recommended by our company. Otherwise the operator or others
in the vicinity could suffer serious injuries, or the tool could be damaged.
The following information should be provided when ordering spare parts:
• Type of machine
• Item number of the machine

16. Warranty

For this electric tool, the company provides the end user - independently
from the retailer's obligations resulting from the purchasing contract -
with the following warranties:
The warranty period is 24 months beginning from the hand-over of the
device which has to be proved by the original purchasing document. For
commercial use and use for rent, the warranty period is reduced to 12
months. Wearing parts, rechargeable batteries and defects caused by
the use of non fitting accessories, repair with parts that are not original
parts of the manufacturer, use of force, strokes and breaking as well as
mischievous overloading of the motor are excluded from this warranty.
Warranty replacement does only include defective parts, not complete
devices. Warranty repair shall exclusively be carried out by authorized
service partners or by the company's customer service. In the case of
any intervention of not authorized personnel, the warranty will be held
void.
All postage or delivery costs as well as any other subsequent expenses
will be borne by the customer.

17. Technical Details

Model
Rated Voltage
Nominal Frequency
Nominal Consumption
No-load Speed
Cutting Width
Line Diameter
Line Length
Line Feed
Weight
Sound Pressure Level
Vibration
Interference suppressed in accordance with EN 55014 and EN 61000.
The machine comply with the safety class II/VDE 0700
We reserve the right to make changes to the technical specifications.
The devices are manufactured in accordance with the provisions of EN
60335-1 and EN 50636-2-91 and fully comply with the provisions of the
German Product Safety Act.
GB-5
RT 1525DA RT 1530D
(EGT-350) (EGT-520)
V~ 230 230
Hz 50 50
W 350 520
min 10.000 10.000
-1
cm 25 30
mm 1,3 - 1,5 1,4 - 1.6
m 2 x 4 2 x 4
Tap'n go Tap'n go
kg 2,1 2,9
82 86,4
dB (A)
K=3,0 dB(A)
m/s² < 2,5 3,9
K=1,5 m/s 2
K=3,0 dB(A)
2
K=1,5 m/s