Know Your Product; Operation; Prior To Initial Operation - SPARKY TK 65 Instrucciones De Uso

after switching off the saw.
▪ Do not touch the saw blade immediately after opera-
tion. It may be extremely hot and could burn your skin.
▪ Do not use blades with parameters not corresponding
to those mentioned above.
▪ Do not use abrasive wheels (for grinding or cutting).
▪ Do not use dull or damaged blades. Unsharpened or
improperly set blades produce narrow kerf causing
excessive friction, blade binding and kickback.
▪ Do not reach underneath the work piece. The guard
cannot protect you from the blade below the work
piece.
▪ Adjust the cutting depth to the thickness of the work
piece. Less than a full tooth of the blade teeth should
be visible below the work piece.
▪ Never hold piece being cut in your hands or across
your leg. Secure the work piece to a stable platform. It
is important to support the work properly to minimize
body exposure, blade binding, or loss of control.
▪ Never use damaged or incorrect blade flanges or bolt.
The blade flanges and bolt were specially designed
for your saw, for optimum performance and safety of

operation.

▪ Rags, cloths, cord, string and the like should never be
left around the work area.
▪ The tool must be used only for its prescribed purpose.
Any use other than those mentioned in this Manual
will be considered a case of misuse. The user and not
the manufacturer shall be liable for any damage or in-
jury resulting from such cases of misuse.
▪ To use this tool properly, you must observe the safety
regulations, the assembly instructions and the operat-
ing instructions found in this Manual. All persons who
use and service the machine have to be acquainted
with this Manual and must be informed about its poten-
tial hazards. Children and frail people must not use this
tool. Children should be supervised at all times if they
are in the area in which the tool is being used. It is also
imperative that you observe the accident prevention
regulations in force in your area. The same applies for
general rules of occupational health and safety.
▪ The manufacturer shall not be liable for any changes
made to the tool nor for any damage resulting from
such changes.
▪ Power tools must not be used outdoors in rainy weath-
er, or in moist environment (after rain) or in close vicin-
ity with easily flammable liquids and gases. The work-
ing place should be well lit.

Know your product

Before using the power tool, familiarize yourself with all
the operating features and safety requirements.
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
1. On/Off switch
2. Lock-off button
3. Spindle lock button
4. Laser light switch
5. Upper blade guard
6. Motor housing
7. Front handle
Original instructions
8. Laser light housing
9. Bevel scale
10. Bevel adjustment knob
11. Rip fence slot
12. Rip fence lock knob
13(a). Cutting guide notch:0°/90°
13(b). Cutting guide notch:45°
14. Base plate
15. Lower blade guard
16. Outer blade flange
17. Inner blade flange (not shown)
18(a). Blade screw (TK 65)
18(b). Blade bolt (TK 85)
19. Blade
20. Blade guard lever
21. Depth adjustment lever
22. Dust extraction port
23. Back handle
24. Rip fence
25(a). Blade hex key (TK 65)
25(b). Blade spanner (TK 85)
Operation
This power tool is supplied from single-phase alternat-
ing current mains only. It is double insulated according
to EN 60745-1 and IEC 60745 and can be connected
to grounded or not grounded sockets. This power tool
is radio suppressed in compliance with EMC Directive
2004/108/EC.
This power tool is designed for longitudinal and cross
sawing wood in a straight line at bevel angle from 0° to
45°.

PRIOR TO INITIAL OPERATION

▪ Make sure the power supply voltage corresponds to
the value indicated on the name plate with technical
data of the tool.
▪ Always check the position of ON/OFF switch. The
power tool must be connected to the power supply
socket only when this switch is in OFF position. If the
plug is connected to a receptacle while the power
switch is in the ON position, the power tool will start
operating immediately, which could cause a serious
accident.
▪ Make sure that the cord and the plug are in order. If the
replacement of the supply cord is necessary, this has
to be done by the manufacturer or his agent in order
to avoid a safety hazard.
▪ Always inspect the blade. Use only well grinded
blades. Never use blades with cracks and indents or
HSS-blades.
▪ Check if the mobile guard moves freely.
▪ Make sure the work piece or the material is well se-
cured.
WARNING: Always switch off and unplug the
power tool prior to any adjustment, servicing or main-
tenance or in case of mains drop-out.
7
EN