Sterling Power ProCharge ULTRA Manual De Instrucciones página 2

1) Install in cool dry well ventilated space.
2) This product has a high heat tolerance and can be installed in an engine room.
3) This product is ignition protected and can be installed near the batteries.
4) Charger MUST be installed vertically to allow for convection air flow and also in the vertical position
5) The product is drip proof.
6) The product will work in any position but we cannot guarantee the drip proof aspect (only vertically).
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Fit this way up to
comply with UL
accordance and for
ABYC drip proofing
compliance.
1) Ammeter, shows the total current being
produced by the charger.
2) Voltmeter, showing the average voltage being
produced by the charger.
3) Power meter, shows the % power being produced
by the unit and the remaining power available.
4) AC power, shows the AC power is connected and
the product is live. LED flashes if power is available
but the unit is switched off (see on/off later) push
buttons. Setup and up arrow for 5 secs to activate.
5) Auto temp control, shows the battery temp sensor
is connected and operational. If sensor not
connected then the unit will default to a 20 deg C / 69
F charge curve.
6) Shows that the active PFC (Power Factor
Correction is on).
7) Fan speed control, varies depending on temp, 3
speeds.
Battery type
Flooded/Open Lead acid
Sealed Lead acid
AGM Lead acid
GEL Lead acid
LiFePO -Lithium
4
Calcium / Custom
Equalization / Desulph
Quick LED feature guide
Pro
GLOBAL AC Input & Active Power Factor Correction
Progressive DIGITAL software control Charger / Powerpack
www.sterling-power.com
AC Power
Auto Temp Control
Active PFC
Multi Speed Fan
AUTO CONSERVATION MODES
CHARGER MODE
System self test
OK
Fault
SETUP
RoHS
ENTER
compliant
High Voltage AC
8) Standby, charger power system power
requirement very low, unit on low float voltage to
prolong battery life.
9) Fast charge unit on constant current mode.
10) OK, unit operating within normal parameters
11) Fault, fatal fault, needs to be returned for repair.
12) Battery type selector, shows which battery
charger curve in operation (adjustable).
13) Buttons to select charge options (see later in
instructions) also used to switch unit off or on in
conjunction with the setup button (see 14).
Off select button press down button for 5 seconds.
On select button press up button for 5 seconds.
14) Button to enter selections. Also, use to switch
unit on/off in conjunction with the up or down button.
15) Battery health program, unit doing a 21 day de-
sulphation cycle.
Preset 1 Profiles
x 2 all voltages for 24V unit x 3 for 36V x 4 for 48V
High Charge V Float Charge V
14.8 13.6
14.4 13.6
14.3 13.3
14.0 13.7
13.8 13.8
15.1 13.6
15.5 15.5
Installation
Charge U
LTRA
Warm air
out
Sterling Power
CEC
www.sterling-power-usa.com
approved
Volts Amps
100%
0%
1 2 3
Charger Output
Stand-by Battery Health Program
Absorption
Float
Fast Charge
De-sulphation
CHARGE INFORMATION
Battery Type
Open lead acid DC Output Fault
DC Low Voltage
Sealed lead acid
DC High Voltage Trip
A.G.M
High Charger temp trip
GEL
Lithium (LiFePO )* Check Fan
4
Calcium / Custom
*Lithium must be used in conjunction
with a lithium balancing system.
WARNING Low Voltage DC
Cooling
Air flow
Maintenance V High Charge V
12.8 14.7
12.8 14.6
13.0 14.6
13.2 14.4
13.2 14.6
13.2 Your choice see custom setup in instructions
15.5
Safety Certified by: TUV
Built and tested to
UL 1236 SB
CSA C22.2-107.2
16) Absorption , charger on initial charge cycle.
17) De-sulphation cycle operational. For safety
reasons only available when on open lead acid
battery type.
18) Float, unit on float charge or power pack mode,
main charge complete.
19) DC output service, output working correctly.
20) DC output low voltage warning, either batteries
are very low / more power is being taken than the
charger can supply / or the charger is defective.
21) High voltage trip, the unit is defective and
tripped itself, or a high back DC voltage has been
detected, like a wind generator reg gone defective.
22) High charger temp, if the unit is positioned in too
hot an environment and over heated, or the fans
have failed.
23) Check fans, if LED on, fans are defective.
24) Case screws to access the wiring of the product.
Preset 2 Profiles
Float Charge V
13.4
13.4
13.6
13.8
14.6
15.5
15
16
17
18
19
20
21
22
23
24
Lithium Users Read
This charger must not be used
to charge lithium battery cells
by itself. You cannot charge
lithium cells on their own. You
must have a lithium balancing
device in conjunction with this
charger.
Maintenance V
12.8
12.8
13.0
13.2
13.2
.