Quick-Programming - SEVERIN MW7868 Instrucciones De Uso

Ocultar thumbs Ver también para MW7868:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 45
Combi 3
Combi 4
1.
Press
repeatedly until the desired combination function is shown.
2.
„C-1", „C-2", „C-3" or „C-4" are fl ashing in the display, in addition, the corresponding symbols (
3.
Press
to confi rm the selected combination function.
4.
Turn the rotary control to select the cooking time.
5.
Press
to start the cooking process. The corresponding symbol for the selected function fl ashes on the display.
The hot-air function
With this function, hot air circulates inside the oven, achieving an even cooking and browning process. By pressing the
cooking temperature can be set within a range of 150°C and 240°C. The cooking time can be pre-set to a maximum of 95 minutes.
If required, the appliance may also be pre-heated. Select the desired temperature level and press
Example: the appliance is to be pre-heated to 200°C, followed by a cooking time of 30 minutes.
1.
Press
6 times. 200°C starts fl ashing on the display, and the symbol
2.
Press
to confi rm the temperature setting.
3.
Press
to start the pre-heating process.
4.
The symbol
and the illuminated indicator bar start fl ashing while pre-heating is in progress.
5.
As soon as the pre-set temperature has been reached, two beeps are heard and the indicator '200°C' starts fl ashing.
6.
Open the door, place the food inside the oven compartment and close the door again.
7.
Turn the rotary control until 30:00 appears in the display.
8.
Press
to start the cooking process. The symbol
Note:
1.
The cooking time cannot be set while pre-heating is in progress.
2.
If the cooking time is not set within 5 minutes after pre-heating is complete, 5 beep signals are heard and the unit will
automatically go back to Stand-by mode.
Note: Steps 3-7 can be omitted, if pre-heating is not required.
Defrost programme according to time or weight (
This defrosting programme is useful for defrosting food by either setting the weight of the food to be defrosted, or by directly setting
the defrosting time. For delicate food we recommend defrosting on the level 'Low' (see table Power setting), to ensure that the food is
defrosted with an even, low temperature setting.
The indicator 'dEF1' represents weight-based defrosting; 'dEF2' represents time-based defrosting.
Helpful notes:
∙ The defrosting proces s should be interrupted at regular intervals and those food portions already defrosted should be taken out;
this is to ensure that food already defrosted will not take away heat from food that still requires defrosting.
∙ Should the food not be completely defrosted after the pre-set defrosting time has elapsed, it is advisable to limit any further
defrosting times to 1-minute periods until the food is fully defrosted.
∙ Food stored in plastic containers or wrapped in plastic should be left standing for a while after it has been taken from the freezer.
Wait until the food can be easily detached from the plastic, before it is put into the oven inside a container suitable for use with
microwave ovens.
1.
Press
once or twice. The display shows 'dEF1' or 'dEF2' and, in addition, the symbols
2.
Use the rotary control to set the weight of the food to be defrosted (between 100g and 2000g) or the desired defrosting time
(between 00:05 and 95:00).
3.
Press
to start the defrosting process. An acoustic signal is heard, and the symbols

Quick-programming

The most commonly used microwave time-settings can be called up simply by pressing
setting is always 100 %. Each press on the key adds 30 seconds to the cooking time.
Note: the cooking process starts as soon as the key is pressed for the fi rst time.
Example: to programme the microwave function for a cooking time of 2 minutes at 100 % power.
20
C-3
C-4
fl ashes on the display.
)
appears.
. With this function, the microwave power
,
,
) are shown.
twice.
and
.
and
start fl ashing.
key, the
Tabla de contenido
loading

Tabla de contenido