Learning Commands - Audio Solutions AS-UNVREM Manual Del Usuario

Repeat step 7 above and lock in the code.
If the indicator light on the top of the remote flashes twice after your pressing of
"Power" key, you are already at the last code of the library. Press "SET" key to resume
the Remote and repeat the above procedures carefully to search again.
3. HOW TO OPERATE THE REMOTE
NORMAL OPERATION ON THE REMOTE SIDE
Once you have set up the Remote for your A/V equipment, it works like your
original remote control. To operate, just aim it at your equipment, press an
appropriate device mode key and invoke the desired function by pressing a
corresponding key on the remote. The indicator light on the top of the remote
flashes during signal transmission and as confirmation of key touch.
CONTROL OF YOURAUDIO SOLUTION DEVICES
Press AS button once, the led indicator will flash once, now you can use the keys
with white background.
PUNCH THROUGH
Punch Through Channel - Punch through channel allows you to operate channel
up and down without having to switch the device modes repeatedly even when
your remote is in other operating modes.
To activate the punch through channel setting:
1. Press desired Device Mode Key of the device in use.
2. Press and Hold "CH +" key.
3. Press desired Device Mode Key of the device you want to change the channel on.
4. Release "CH +" (the indicator light on the top of the remote flashes once if the
setting is activated).
To deactivate the punch through channel setting:
1. Press desired Device Mode Key of the device in use.
2. Press and Hold "CH -" key.
3. Press desired device Mode Key of the device you want to change the channel on.
4. Release "CH -" (the indicator light on the top of the remote flashes twice if the
setting is activated).
PUNCH THROUGH VOLUME
Punch through volume allows you to operate volume up and down without
having to switch the device modes repeatedly even when your remote is in other
operating modes.
To activate the punch through volume setting:
1. Press desired Device Mode Key of the device in use.
2. Press and Hold "VOL +" key.
3. Press desired Device Mode Key of the device you want to change the volume on.
4. Release "VOL +" (the indicator light on the top of the remote flashes once if the
setting is activated).
To deactivate the punch through volume setting:
1. Press desired Device Mode Key of the device in use.
2. Press and Hold "VOL -" key.
3. Press desired Device Mode Key of the device you want to change the volume on.
4. Release "VOL -" (the indicator light on the top of the remote flashes twice if the
setting is deactivated).
MACRO POWER
Macro Power allows you to turn two of your A/V equipment on/off
simultaneously.
To activate the macro power setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "Power" key.
3. Press desired Device Mode Key (e.g. STB).
4. Release "Power" key (the indicator flashes once if the setting is activated).
To deactivate the macro power setting:
1. Press desired Device Mode Key (e.g. TV).
2. Press and Hold "Power" key.
3. Press desired Device Mode Key (e.g. STB).
4. Release "Power" (the indicator flashes twice if the setting is deactivated).

LEARNING COMMANDS

Your Remote is equipped with learning capability. This allows you to "teach" your
Remote certain functions from your original equipment remote. Please follow the
steps below.
1. Press the desired device mode key (e.g. TV).
2. Hold down "LEARN" key for 3 seconds until the red indicator flashes once and stay lit.
3. Place the Remote and your device remote on a flat surface, aimed at each other
1-3 inches apart.
4. Press a desired key once and release on the Remote which you want to learn the
command. The red indicator will flash twice then stay lit.
5. Press and keep holding the key on your original equipment remote which you
want to learn for a few seconds.
6. When the red indicator light flashes once and stays lit continuously, the
command has been learned successfully and you can release the key on your
original equipment remote. If the red indicator light flashes three times quickly,
it shows an error in the learning process. Adjust the position of both remotes and
repeat from step 4 again.
2