Audio Solutions AS-UNVREM Manual Del Usuario página 2

UNIVERSAL REMOTE CONTROL WITH LEARNING FUNCTION
Congratulations! Your Universal Remote Control is a state-of-the-art device which
integrates 6 different infra-red remote controls to deliver instant A/V action to
your fingertips. Before operating the remote, please read this manual thoroughly
and carefully! Then store it properly for future reference.
1. HOW TO INSTALL NEW BATTERIES
2 x AAA 1.5V or equivalent Alkaline batteries are recommended.
1. Remove the battery cover on the back of your remote.
2. Insert the batteries observing the "+/-" marks inside the battery compartment.
3. Push the battery cover back in place.
NOTE: The memory inside the remote will retain its settings for short periods of time
with the batteries removed (When changing batteries for instance).
2. HOW TO SETUP THE REMOTE
BY ENTERING THE DEVICE CODE
You may setup the remote by following the code entering instructions.
1. Go to the DEVICE CODE LIST at the end of this manual, look up the 4-digit
Device Code which corresponds to the brand of your A/V equipment. If there is
more than one Device Code listed under your brand, start from the first code.
2. Press the desired Device Mode Key (e.g. TV).
3. Hold down "SET" key on the remote simultaneously for 2 seconds until the
indicator light on the top of the remote lights up.
4. Use the number keys "0" - "9" to enter your 4-digit Device Code. The
indicator should go out after the 4th digit is entered.
Turn on your device (e.g. TV), then try the function keys on the remote. If your
device (e.g. TV) responds to your activated function correctly, you have entered
the right Device Code. Otherwise, repeat the above steps with the next available
Device Codes until your device (e.g. TV) responds to your activated function, and
most keys work correctly.
* Simply repeat the above procedures to enter the Device Codes for your DVD,
SAT, CBL and VCR devices. (Remember to press the correct Device Mode Key
in step 2 above)
NOTE: If the indicator light flashes twice in step 4, a wrong Device Code has been
entered. You are required to repeat step 2 to 4 again.
SUGGESTION : If you cannot find a correct Device Code for your equipment, see .
"HOW TO SET UP THE Remote - BY SEARCHING THROUGH THE LIBRARY".
For future reference you are recommended to take a note of your Device Codes in the
space provided on the product's back label after setting up the remote correctly.
BY SEARCHING THROUGH THE LIBRARY
If you cannot identify a correct Device Code for your equipment from the
Device Code list, you may search for the code in the library:
1. Turn on your device manually (e.g. TV).
2. Press a desired Device Mode Key (e.g. TV).
3. Hold down "SET" key on the remote simultaneously for 2 secondsuntil the
indicator on the top of the remote lights up.
4. Enter a corresponding Magic Search Code from the following table. The indicator
light on the top of the remote should go out after the 4th digit is entered.
DEVICE TYPE:
MAGIC SEARCH CODE: 0001
(e.g. press "TV" device mode key, then press "SET" key, and enter TV Magic Search Code 0001.)
5. Press the same desired device mode key again as in step 2 above. (e.g. TV)
6. Hold down "SET" key simultaneously for 2 seconds until the indicator light on
the top of the remote lights up, and your Remote is ready to start searching.
7. Aim the Remote at your device (e.g. TV), press the "Power" key slowly and
repeatedly until the device has been turned off.
Once your device has been turned off, immediately press Device Mode Key
(e.g. TV) to lock the code, the indicator light on the top of the remote will go out.
* Simply repeat the above setup procedures to search for the Device Code for
your VCR, SAT, DVD or CTV. (Remember to press the correct Device Mode
Key and correct Magic Search Code in step 2-5 above)
IMPORTANT: If the power on/off function of your device is not infra-red controlled, you
need to follow steps 2 to 6 above and start searching. Press "Power" and another function key
alternately until your device responds to the expected function, then press the same Device
Mode Key (e.g. TV) to lock in the code.
"Play" alternately.)
NOTE: DVD, CTV and other device codes can be searched for and locked into any
device modes. Simply press the corresponding device mode key in step 2 & 5 and enter an
appropriate Magic Search Code for your DVD, CTV and other devices.
Each time you press the "Power" key , the Remote will skip to the next code and send out a
POWER signal trying to turn off your device. If you fail to stop pressing "Power" key in time
when your device has been turned off, turn your device on again immediately. Before the
indicator on the top of the remote goes out, press "Mute" key on the Remote to skip backwards.
USER MANUAL for Model: AS-UNVREM
TV VCR
0002
(e.g. Press "Power" & "1" alternately, or ; Press "Power" &
1
SAT CTV
0003 0004
DVD
0005