Troubleshooting Guide - Polygroup SUMMER WAVES SKIMMERPLUS SFX600 Manual Del Usuario

WARNING:
UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE FILTER PUMP.
Problem
A Pump not plugged in
1. Pump Motor 3
doesn't start, or
B GFCI Power Cord Set
and/or circuit breaker tripped
kicks on and off
C Low Voltage
A Low pool water level
B Clogged water inlet/outlet
2. No or slow water
flow from the Return
C The Filter Cartridge
Fitting 18
D Motor Rotor block by dirt
A Inadequate chlorine level
B Inadequate pH level
C The Filter Cartridge
3. Pump is not cleaning
D The Filter Cartridge
the pool properly e.g.
cloudy/green water
E Water flow is slow
F Other chemicals required
G Pool water is too dirty
A Hose
with Skimmer Canister
90° Elbow
B Bottom of Canister
4. Water leakage at
C Between Canister
pool wall
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8AM to 5PM MST, Monday-Friday.

TROUBLESHOOTING GUIDE

Cause
A Plug the GFCI Power Cord Set
B Reset your circuit breaker on the electrical panel. If problem persists, have the
26
C Check and make sure the line voltage is between 105VAC and 125VAC.
A Water level must be between the MIN and MAX lines on the Skimmer Seal Ring
B Check for obstructions at the Strainer Basket
7 is too dirty C Clean or replace the Cartridge following the steps of FILTER CARTRIDGE USE & CARE (p. 11).
D Refer to pump servicing instructions to clean dirt.
A Maintain the chlorine level between 1.0 and 1.6 ppm.
B Maintain the pH level between 7.3 and 7.8
C Clean or replace the Cartridge following the steps of FILTER CARTRIDGE USE & CARE (p. 11).
7 is too dirty
7 is damaged D Inspect the Cartridge for holes or tears. If it's visibly damaged, replace it with a new one.
E Check for obstructions at the Strainer Basket
F Have your pool water sample tested by a pool supplies store. You may need to
G Chemicals are essential to keep the pool water clean. Clean the pool and filter more often.
12 – Hose connections
A Check that the Hose Clamps
9 and/or
13 are not secured
B See STEP 3: Pump Reassembly/Replacement, p. 15-16:
9
C Make sure the Skimmer Gasket Rubber Seal
9 and
Extended operating days and hours during peak season requirements.
RESET button to start the Pump.
circuit checked by a qualified electrician.
Return Fitting 18 .
Return Fitting 18 .
add other chemicals since water quality varies in different localities.
11 are properly tightened over both the Hose and the Hose
Connection O-Rings 10 ; adjust and retighten if necessary. Also, check the Hose for cracks
or holes and replace as needed.
B1. The Canister Gasket 4 must sit in the groove (inner groove for SFX600/SFX1000) on
the bottom of the Canister before installing the pump.
B2. Check Pump alignment. The arrow of the Pump indent (marked "ALIGN") MUST point
to the Canister indent (only visible from bottom).
B3. Make sure the Motor Seal Nut
See SETUP INSTRUCTIONS (3) & (4), p. 9:
- The two keys of the Gasket should be at the top.
- The pool liner is not trapped in the threads.
- No gaps between the Gasket and the Canister.
- The Skimmer Seal Ring 22 is firmly tightened onto the Canister.
OWNER'S MANUAL
Solution
26 to a grounded power outlet. Then press the
24 , Filter Cartridge 7 , Hose
24 , Filter Cartridge
1 is not cross-threaded.
25 is installed properly.
22 .
12 and
7 , Hose 12 and
17