General Inspection; Troubleshooting - Triton TRA 001 Instrucciones De Uso

Note: Whilst this product was designed for efficient and convenient operation on most router
tables, it is particularly suited for use with the Triton Router Table RTA300 and TWX7RT001.
Note: Router adjustments are extremely easy using the unique features described
earlier in the manual. See 'Collet and cutter installation' and 'Cut Depth Adjustment'.
Note: The plunge spring MUST be removed before this router is fitted into a router table:
1. Set the router at the top of its plunge range and engage the Plunge Lock Lever (11)
2. Loosen the small screw next to the Plunge Spring Access Cap (21) a few turns.
3. Holding the Plunge Spring Access Cap firmly so that the spring will not shoot
upwards when released, twist the cap anti-clockwise to remove it, (Image O)
4. Remove the spring and store in a safe place.
5. Replace the Plunge Spring Access Cap and re-tighten the screw.
NOTE: Be sure to re-fit the plunge spring before using the router freehand.
• The Table Height Winder (24) engages with the Table Height Winder Connection Point (14)
for quick and easy above-the-table height adjustment when the router is table-mounted
Accessing the baseplate screw threads
1. To mount the router in a third-party router table or a table of your own construction
remove the 4 x screws of the baseplate indicated in Image Q and remove the baseplate
2. There are 2 sets of screw threads as shown in figure II. There are 4 x ¼
UNC screw threads (A) which are used to secure the baseplate as well as
suitable for table mounting plus an alternate set of 3 x M6 threads (B)
Note: The M6 threads are not available on earlier versions of the TRA001 router.
Accessories
• A wide range of suitable accessories for this tool are available from your Triton stockist,
including a large selection of cutter/router bits. Spares including carbon brushes, guide
bushes and collets are available from your Triton stockist or www.toolsparesonline.com.
Maintenance
WARNING: ALWAYS disconnect from the power supply before
carrying out any inspection, maintenance or cleaning.

General Inspection

• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear.
Repairs should be carried out by an authorised Triton service centre.
This advice also applies to extension cords used with this tool

Troubleshooting

Problem
No function when On/Off Power Switch
(8) is operated
Inaccurate cutting profile
GB
Router will not operate
Router runs or cuts slowly
8
Possible cause
No power
Defective On/Off Power Switch
Depth Stop (3) not correctly adjusted
Incorrectly fitted or loose router bit/Collet (23)
No supply of power
Brushes worn or sticking
Switch is faulty
Motor components faulty or short circuited
Blunt or damaged cutter
Speed Controller (10) set low
Motor is overloaded
Cleaning
WARNING: ALWAYS wear protective equipment including
eye protection and gloves when cleaning this tool.
• Keep your tool clean at all times. Dirt and dust will cause internal
parts to wear quickly, and shorten the device's service life
• Clean the body of your machine with a soft brush, or dry cloth
• Never use caustic agents to clean plastic parts. If dry cleaning is not
sufficient, a mild detergent on a damp cloth is recommended
•
Water must never come into contact with the tool
• Ensure the tool is thoroughly dry before using it
• If available, use clean, dry, compressed air to blow through
the ventilation holes (where applicable)
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible sparking
• To replace the brushes, remove the two Brush Access Covers (9). Carefully
remove the worn brushes (Image P) and ensure the sockets are clean. Carefully
replace with new brushes and then replace the Brush Access Covers
• After fitting run the router without load for 2-3 minutes to help the brushes
bed in. The process of the brushes fully bedding in may take repeated uses.
Motor sparking may continue until new carbon brushes have bedded in
• Alternatively, have the machine serviced at an authorised service centre
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of power tools
that are no longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and
electronic equipment (WEEE), with household waste
• Contact your local waste disposal authority for information
on the correct way to dispose of power tools
Check power supply
Replace the On/Off Power Switch at an authorised Triton service centre
Ensure that the Depth Stop corresponds to the maximum amount of cut permitted by the Turret
Stops (1)
Tighten router bit/Collet and cutter assembly
Check that power is available at source
Disconnect power, open Brush Access Covers (9) and ensure brushes are not damaged or heavily
worn
Have the tool serviced by an authorised Triton service centre
Re-sharpen or replace cutter
Increase variable speed setting
Reduce pushing force on router
Solution