Ergonomic And Collapsible Bed Rail 1,40 M, For Compact Beds - JANE 50295 S58 Instrucciones De Uso

Ocultar thumbs Ver también para 50295 S58:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 1
EN

Ergonomic and collapsible bed rail 1,40 m, for COMPACT beds

IMPORTANT: KEEP FOR FUTURE REFERENCE.
Read the entire instruction before assembling and installing this product.
If you sell or give away this product, make sure you give this instruction to the new owner.
Make sure that no parts are missing before fitting the rail (see parts list).
This bed rail complies with BS 7972:2001+A1:2009 - Made in China - Designed in Spain.
WARNING
1-The bedguard should not be used for children under the age of 18 months or when the child is over the age of 5 years. This
bed rail is used only when the child is able to climb in and out of bed unaided.
2-The bedguard should not be used as a substitute for a a cot, as it cannot provide the same level of safety as a cot.
3-Suitable for use with beds of the following sizes: minimum 80x190 cm and maximum: 140x200 cm. and mattress with a
thickness of between 15 to 30 cm.
4- Once installed, make sure the bed rail is correctly fitted and is secure.
5-The bedguard should not be used on a sleeping surface that is more than 600 mm from the floor. Never use on a bunk bed,
a child's bed or any other bed hat does not correspond to the present instructions.
6-To avoid risk of injury, carefully respect the present instructions when assembling, installing and using this bed rail.
7-Do not leave the child unattended while fitting or dismantling this product; the child should always be under an adult's supervision.
8-It should be checked periodically that the bed rail is always properly fitted and secure in place, and the locking mechanism on
the bedrail are securely fixed. The bedguard should be periodically checked for its general condition with particular reference
to the security of any locking mechanism and/or hinges that are used on the product.
9-Keep away from fire.
10-Do not use accessories that have not been approved by JANÉ. Additional and replacement parts should be obtained only from
the manufacturer.
11-The bedguard should not be used unless the fixings are in place and securely attached to both the bed and/or the mattress
and the bedguard.
12-This bed rail is suitable for all types of bed bases.
The images in the photographs in the step-by-step assembly guide may have a design that is different from the model you have
purchased.
Make sure that the box contains all the parts before starting to assemble the bed rail.
PARTS - See the diagram on page 2 and check that you have:
A- 2 lower bars and the collapsible mechanism with fastening straps, which form a U-shaped bar when joined (A and A1)
B- 2 bars which, after joining them together, form a long, rounded bar (B and B1)
C- 2 bars which, after joining them together, form a long, flat bar (C and C1)
D- 2 L-shaped upper bars, which form a bridge when joined (D and D1)
E- 1 piece of fabric to cover the bed rail (E)
F- 1 travel bag to carry the bed rail (F)
ADJUSTMENT AND FASTENING POINTS (see diagram H on page 2)
1. Tunnel 1 (top)
2. Tunnel 2 (bottom)
3. Side zips
4. Bed rail skirt
ASSEMBLY - See page 3 and consult the diagrams on page 2 if necessary
•Take one of the D bars that has a fastening hole (see diagrams in chart 1, page 3) and attach it to one of the A bars. Note:
First join the three parts of the collapsible mechanism as shown in diagram 2.1 on page 3. You will hear it click into place
when properly connected. The bar will now look like diagram 2.2 on page 3.
•Once you have joined these two bars, insert them into the fabric to cover the bed rail E and pass these two bars through the
top and bottom tunnels inside the fabric until the cover is on fully. Then fasten the side zip. (See diagrams in chart 3)
•Next, take the symmetrical bars A and D,repeat the previous step and connect each opposing end to the previous bars. When
you have heard them click into place, slide the cover down the side and fasten the zip so it fits snugly. (See diagram in chart 4)
•NOTE: Pay special attention when fitting the bed rail cover on the metal structure. Make sure that the Velcro is on the
EXTERIOR part of the bed rail so the child cannot access it while in bed! This will prevent the child from being able to take
the cover off the bed rail during the night.
• Join the two B-B1 rounded bars and insert them into the skirt of the fabric connecting them to the plastic side structure of
the bed rail. Push the plastic cover upwards until you hear it click locked. (See diagrams in chart 5)
•Fasten the Velcro on the sides of the skirt to the plastic structure so the fabric is fully fitted to the bed rail. (See diagrams in
chart 6)
•Join the two C-C1 flat bars. Make sure they click securely into place. Fasten it to the end of each side of the metal structure
with the straps, to make the stabiliser foot. See photo 7. This is the part that goes underneath the mattress on top of the bed
frame using the stoppers on the straps to prevent the bed rail from moving.
•Lastly, fit the screws into the corners to secure the stabiliser foot in place so it can be inserted underneath the mattress.
See photo 8.
5. Stabiliser foot
6. Side adjustment Velcro
7. Click system for collapsing the rail
6
Tabla de contenido
loading

Tabla de contenido