Makita SG1250 Manual De Instrucciones página 5

ENGLISH
(Original instructions)
1 Shaft lock
2 Notch
3 Scale
4 Clamping screw
5 Slide switch
6 Hex socket head bolt
7 Blade case
8 Base
SPECIFICATION
Rated speed (n) / No load speed (n
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for cutting tracks in concrete walls or
cutting in ferrous materials or concrete drainage chan-
nels with a diamond wheel but without using water.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
ANGLE CUTTER SAFETY WARNINGS
Safety Warnings Common for Abrasive Cutting-Off
Operations:
1. This power tool is intended to function as a cut-
off tool. Read all safety warnings, instructions,
illustrations and specifications provided with
this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Explanation of general view
9 Shaft lock button
10 Lock nut
11 Lock nut wrench
12 Diamond wheel
13 Space ring 6 (6 mm thick)
14 Space ring 3 (3 mm thick)
15 Front handle
16 Cam
Model
Wheel diameter
European countries
)
0
Spindle thread
Overall length
Net weight
Safety class
ENE026-1
ENF002-2
GEA010-1
GEB042-3
Other countries
2. Operations such as grinding, wire brushing, pol-
ishing are not recommended to be performed
with this power tool. Operations for which the
power tool was not designed may create a hazard
and cause personal injury.
3. Do not use accessories which are not specifi-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
4. The rated speed of the accessory must be at
least equal to the maximum speed marked on
the power tool. Accessories running faster than
their rated speed can break and fly apart.
5. The outside diameter and the thickness of your
accessory must be within the capacity rating of
your power tool. Incorrectly sized accessories can-
not be adequately guarded or controlled.
6. The arbour size of wheels, flanges, backing pads
or any other accessory must properly fit the
spindle of the power tool. Accessories with arbour holes that do not match the mounting hardware of
the power tool will run out of balance, vibrate exces-
sively and may cause loss of control.
7. Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive
wheels for chips and cracks, backing pad for
cracks, tear or excess wear, wire brush for loose
or cracked wires. If power tool or accessory is
dropped, inspect for damage or install an undam-
aged accessory. After inspecting and installing
an accessory, position yourself and bystanders
away from the plane of the rotating accessory
and run the power tool at maximum no-load
speed for one minute. Damaged accessories will
normally break apart during this test time.
17 Dust nozzle
18 Vacuum cleaner
19 Hose
20 Hex wrench
21 Inhalation vent
22 Exhaust vent
SG1250
125 mm
–1
10,000 (min
–1
9,000 (min
M14
346 mm
4.4 kg
/II
)
)
5