33. Never connect the compressor to an engine
generator or direct-current power supply
The compressor will break or be damaged from burning.
34. This compressor is for indoor use. Do not install
the compressor in any place exposed to rain or
splashed water, high-humidity place or high-
temperature place (Fig. 1)
If used in the wet condition, it could produce an electric
shock or be short-circuited, resulting in ignition. Use
it under the environmental conditions provided by its
specifi cations.
35. Do not operate the tool near a fl ammable substance
Never operate the tool near a fl ammable substance (e.g.,
thinner, gasoline, etc.). (Fig. 2) Volatile fumes from these
substances could be drawn into the compressor and
compressed together with the air and this could result in
an explosion.
SPECIFICATIONS
Model
Power supply
Rated current
Motor power
Protective earthing
Protective structure
Working temperature
Working humidity
Height above sea level
Storage temperature
Storage humidity
Pressure switch working range
INSTRUCTIONS FOR OPERATION
Unpack the compressor and check for any defi ciency,
damage caused during transportation and loose bolts and
screws.
WARNING
Read section titled "SAFETY WARNINGS"
Wear safety glasses or goggles
Danger to the eyes always exists due to the possibility of
dust being blown up by the exhausted air or of a fastener
fl ying up to the improper handling of the tool. For these
reasons, safety glasses or goggles shall always be worn
when operating the tool.
NOTE:
○ Non-side shielded spectacles and face shields alone do
not provide adequate protection.
○ The information contained in this Instruction Manual
is designed to assist you in the safe operation and
maintenance of the compressor.
Some illustrations in this Instruction Manual may show
details or attachments that diff er from those on your own
compressor.
36. Never use the tool in an explosive atmosphere
Sparks from the tool may ignite atmospheric gases, dust
or other combustible materials.
37. Be sure to earth the compressor
Earth the compressor to prevent a worker from getting
an electric shock. It comes with a 3-pole cord and a
3-pole earthing plug so that it can be connected to an
appropriate earthing plug socket.
A green-and-yellow striped wire is an earthing conductor.
Never connect it to other charged terminals.
38. When carrying the compressor, hold it correctly.
Carry the compressor in a proper manner by holding its
grips with both hands. (Fig. 3)
39. Take care to transport the compressor correctly, do
not overturn it or lift it with hooks or ropes.
40. When disposing the machine or tis parts, follow the
relevant national rules.
950 W (1.27 HP)
85 % RH or less. No dew condensation.
85 % RH or less. No dew condensation.
Off : 3.25 MPa (32.5 bar) [471.4 psi]/On: 2.6 MPa (26 bar) [377.1 psi]
1. Installation
WARNING
○ Never use the machine in a place where any volatile
combustible substance has been stored. (Fig. 2)
Never use it near gasoline, thinner, gas, paint or adhesive
agent, because they could be ignited or blow up.
○ Never use the machine near the heat of fi re or any
combustible substance.
○ Never use the machine in an unstable place. (Fig. 4)
Never use it in a place where it could move or fall of itself.
Be sure to install the compressor on a fl at fl oor, with leg
rubber underneath it; the allowable tilt angle of the fl oor
is up to 10 degrees. If the installation fl oor is tilted and
slippery, ensure that the compressor does not move
during operation. Do not use it on a shelf or a stand where
it may fall or tumble.
○ Avoiding a place exposed to high temperature or
the direct sunshine, be sure to use the machine in
the well-ventilated shade.
Using it under high temperature or in the direct sunshine
not only deteriorates its durability, but increases the
temperature of the main body, causing danger to your
safety.
Be sure to use it in the well-ventilated shade. The
adequate room temperature is +5°C to +40°C.
EC1433H
230 V AC 50Hz
5.2 A
Class I
IP20
5°C to +40 °C
Up to 1000 m
-10 to +50 °C
English
7