Know Your Product; Operation - RS Components Lithium-Ion Instrucciones De Uso

in red (overheat standby). The fan in the charger auto-
matically starts running to cool the hot battery down to
normal temperature. After cooling, indication changes to
red glowing and charging begins.
3) This charger detects charge status and transfers to
fine charging mode when the battery has been almost
fully charged and keeps the battery in full charge state.
-
-
tO Obtain tHe best life fOR tHe
R
batteRy
▪ Do not recharge battery after a short operation to
d
avoid decreasing operation time and battery capacity.
r
▪ When battery is not in use, keep it away from other
d
metal objects like paper clips, coins, keys, nails,
screws, or other small metal objects that can make
a connection from one terminal to another. Shorting
-
the battery terminals together may cause fire or ex-
r
plosion.
▪ Always unplug the charger when not in use and store
in a dry secure place.
▪ Do not charge battery packs and do not store the
charger in premises where the temperature may drop
-
under 32ºF (0ºC) or exceed 104°F (40°C).
.
batteRy state inDicatiOn
The battery state during operation can be checked on
the LED display (7) by pressing the indicator button (8).
(Fig. 1)
1 = Battery 70 - 100% charged
2 = Battery 30 - 69% charged
3 = Battery less than 30% charged
o
4 = Battery flat of defective
y
VII - Know your product
e
Before using the power tool, familiarize yourself with all
d
operating features and safety requirements.
y
Use the tool and accessories only for the applications
intended. All other applications are expressly ruled out.
g
1 Locking sleeve
2. Bit holder
-
3. LED light
,
4. Forward/reverse switch
s
5. ON/OFF trigger switch
6. LED light button
-
7. LED battery state indicator
.
8. Battery state indicator button
9. Battery release button
10. Battery
11. LED chargе state indicator
12. Charger
VIII - Operation
leD WORk aRea ligHt
The machine is equipped with LED light (3) to illuminate
the work area and improve visibility when drilling in areas
- with insufficient light. To turn the LED light on and off de-
s press the LED light button (6).
Original instructions
RS-754-1930-pages-GUR 15Li.indd 7
Work light will automatically turn off 10 minutes after it
has been switched on.
ReveRsing
The extreme position of lever (4) to the right (viewed from
the rear) is equivalent to anti-clockwise rotation, the ex-
treme position to the left - to clockwise rotation. When
the ON/OFF switch (5) is depressed lever (4) can not be
actuated. (Fig. 2)
WaRning: Reversing can be performed only
when the spindle is not rotating!
Drilling and tightening screws are performed with lever
in extreme position to the left. Removal of screws is per-
formed with lever in extreme position to the right.
sWitcHing On - sWitcHing Off
switching on: press ON/OFF switch (5).
switching off: release ON/OFF switch (5).
The power tool is equipped with a brake. The spindle stops
rotating immediately after releasing the switch lever.
smOOtH electROnic Rpm cOntROl
Light pressure on ON/OFF trigger switch (5) results in
low rotation speed, further pressing the switch results in
smooth increase of the rpm to maximum upon reaching
the extreme position.
OpeRating tHe tOOl
Impact operation starts automatically when the load ex-
ceeds certain level. Pushing the trigger switch at no load
will result only in change of speed.
The fastening torque depends on the duration of impact
operation. Generally, maximum torque is achieved after
3 to 10 seconds of impact operation. Further operation
will result only in slight torque increase. Prolonged im-
pact operation may cause motor damage or burning.
The torque depends on the length, grade and diameter
of the screw. It depends also on the strength of material
to be fastened (wood, metal, etc.) and the type of washer
used. Operate the tool after calculating the appropriate
impact operation time by performing a trial fastening
and measuring the actually achieved torque by a torque
wrench.
WaRning: Power tool with a faulty switch is
dangerous and shall be repaired before use.
inseRting anD RemOving bits (Fig. 3)
WaRning: Remove the battery or set the
forward/reverse switch (6) in central (neutral) position.
inserting the bit:
1. Pull the locking sleeve (1) forward.
2. Insert the bit into the hexagonal socket of the bit
7
EN
8.6.2012 г. 15:20:36 ч.