Fault Symptoms - Worx Landroid WG794 Manual Del Usuario

Fault symptoms

®
If your Landroid M does not work correctly, follow the trouble shooting guide below. If the fault persists, contact your dealer. Refer
to the Owner's Manual for Landroid
Symptom
®
Landroid M turns on, but
the Blade Disc does not
move.
®
Landroid M vibrates.
Grass is being cut
unevenly.
The LED light on the
Charging base does not
turn on.
Green light flashing on
charging base.
The charging time is far
more than 2h.
The mower does not
charge.
®
Landroid M is starting to
have shorter run-times
between charges.
®
Landroid M is not operating
at the correct time.
®
Landroid M can not
correctly dock with the
Charging Base.
The Green light on the
Charging Base turns
ON before charging is
complete.
®
M component information.
Cause
®
Landroid M is searching for the Charging
Base.
Blades may be damaged. Check condition of
the Blade Disc.
®
Landroid M does not work enough hours
per day.
Mowing area is too big.
Blades are dull.
The cutting height is set too low for the
length of the grass.
Grass or other object has wrapped around
the blade disc.
There is a build-up of grass in the Blade Disc
or Motor Frame Box.
There is no power.
The Boundary Wire isn't connected.
Poor connection caused by debris on the
Charging Strip.
The charging protection program has
activated due to high temperature.
There is no power.
The Boundary Wire isn't connected.
Does not operate correctly while manually
charging.
Something is clogged in the Blade Disc.
®
Landroid M is shaking heavily.
The battery may be exhausted or old.
The clock is not set to the correct time.
The times set of the Landroid
stop mowing are incorrect.
Environmental influences.
The charging base is overheating, the LCD
will display "Over temperature".
®
The Landroid M is on standby mode as it is
not the programmed working time.
This is normal, the Landroid
Blade Disc does not rotate while it is searching for the
Charging Base automatically.
Check the Blades, and replace them if damaged.
Clean the debris or foreign objects on the blades and
blade disc.
Add more hours to the mowing time.
Try decreasing the size of the mowing area or adding
more hours to the mowing time.
Change all the Blades and screws in order to balance
the Blade Disc.
Raise the cutting height and then gradually lower.
Check the Blade Disc and remove the grass or other
object.
Make sure the Blade Disc rotates easily. If needed, you
may take off the Blade Disc and then remove the debris.
See How to Clean.
Check that the power cord is connected properly and
that the power source is sufficient.
Check that the Boundary Wire has been connected
correctly or that it has not been broken off.
Clean the Contact Pins located on the Charging Base
and the Charging Strip on the Landroid
Place the charging base in a shady area or wait until the
temperature has cooled down.
Check that the power cord is connected properly and
that the power source is sufficient.
Check that the Boundary Wire has been connected
correctly or that it has not been broken off.
Connect the charger base while the machine is off.
Before the LED light of the charging base turns green
from red, press ON/OFF Key to start charging. It is ok
when the screen display "charging".
Take off the Blade Disc and clean it.
The grass is too high and too thick.
Check the Blade Disc and Blade, remove the grass or
other object.
Replace a new battery.
Set the clock.
®
M to start and Change the time settings for the mower to start and
stop.
Restart the Landroid
Place the charging base in a shady area or wait until the
temperature has cooled down.
It's normal.
Action
®
M needs to recharge, the
®
M using a cloth.
®
M.
17
EN