Oursson MD2042 Manual De Instrucciones página 20

unauthorized attempts to test the product or
make any changes in its construction or software
programs, including repair or maintenance in unau-
thorized service centers.
• If the defect of the product was a result of use of
non-standard and/or low quality equipment, acces-
sories, spare parts, batteries.
• If the defect of the product is associated with
its use in conjunction with additional equipment
(accessories), other than additional equipment
recommended for use with this product. The manu-
facturer is not responsible for the quality of the
additional equipment (accessories) manufactured
by third parties, for the quality of its products to-
gether with such equipment, as well as the quality
of the work of the additional equipment together
with the products of other manufacturers.
6. Product defects detected during the lifetime of the
product are eliminated by the authorized service cent-
ers (ASC). During the warranty period, elimination of
defects is free of charge with the presentation of the
original certificate of guarantee and documents that
confirm the fact and date of the contract of retail pur-
chase. In the absence of such documents, warranty
period is calculated from the date of manufacture of
goods. It should be taken into account:
• Setup and Installation (assembly, the connection,
etc.) of the product described in the documentation
attached to it, does not enter the scope of warranty
and can be performed by the user as well as the
specialists of most authorized service centers on a
paid basis.
• Work upon maintenance of products (cleaning and
lubricating the moving parts, replacement of con-
sumables and supplies, etc.) are made on a paid
basis.
7. The manufacturer is not responsible for any damage
directly or indirectlycaused by their products to people,
pets, property, if it occurred as a result ofnon-obser-
vance of the rules and conditions of use, storage,
transportation or installation of the product, intentional
or negligent actions of consumer or third parties.
8. Under no circumstances, the manufacturer is not
responsible for any special, incidental, indirect or con-
sequential loss or damage, including but not limited
to: lost profits, damages caused by interruptions in the
commercial, industrial or other activities, arising from
the use of or inability to use the product.
9. Due to continuous product improvement, design ele-
ments and some technical specifications are subject
to change without prior notice from the manufacturer.
Using the product when after the terms of use (life-
time):
1. Lifetime set by manufacturer for this product applies
only when the product is used exclusively for personal,
family or household needs, as well as the consumer
observes the correct operation, storage and trans-
portation of products. Under thecondition of careful
handling of the product and compliance with the rules
of operation the actual life may exceed the lifetime set
by manufacturer.
2. At the end of the product lifetime, you should contact
an authorized service center for to conduct a pre-
ventive maintenance of the product and determine
the suitabilityfor further use. Work on conducting a
20
preventive maintenance of the products is also made
in service centers on paid basis.
3. The manufacturer does not recommend the use of this
product after the end of its lifetime without its preven-
tive maintenance by the authorized service center,
since inthis case, the product can be dangerous to the
life, health or property of the consumer.
Product Recycling and Disposal
This appliance has been identified in accordance with the
European directive 2002/96/EG on Waste Electrical and
Electronic Equipment – WEEE.
After the expiration of the lifetime, the product cannot be
disposed with another household waste. Instead, it shall be
deposited in the appropriate recycling collection point for
electrical and electronic equipment for proper treatment and
disposal in accordance with federal or local law. By dispos-
ing correctly this product, you will help to conserve
natural resources and preventing the product from
damaging the environment and human health.
For more information on the collection point and
recycling of this product, please contact your local
municipal authorities or the enterprise for house-
hold waste disposal.
Date of manufacture
Each product has a unique serial number in the form of
alphanumeric row and is duplicated with a barcode that
contains the following information: name of the product
group, date of manufacture, serial number of the product.
Serial number is located on the rear of the product, on the
package and the warranty card.
The first two letters-correspondence to the product
group (microwaves – MM/MD).
The first two digits – year of manufacture.
The second two digits – month of manufacture.
The last two digits – serial number of product.
To avoid misunderstandings, we highly
recommend you to read carefully the in-
struction manual and the warranty obliga-
tions. Check the correctness of the war-
ranty card. Warranty card is valid only if the
following are correctly and clearly stated:
model, serial number, date of purchase,
clear stamps, buyer's signature. The se-
rial number and the model of the device
must be the same as in the warranty card.
If these conditions are not fulfilled or the
data specified in the warranty card was
changed, the warranty card is invalid.