Additional Instructions For Work With The Battery Pack - RS Components 18410192476 Instrucciones De Uso

heavy knock, dropped or otherwise damaged in any
way. Do not operate charger with damaged cord or
plug - have them replaced immediately. Take the
charger to an authorised service centre for a check
or repair.
▪ If the replacement of the supply cord is necessary,
this has to be done by the manufacturer or his agent
in order to avoid a safety hazard.
▪ Do not disassemble the charger. Take it to an author-
ised service centre when service or repair is required.
Incorrect re-assembly may result in the risk of fire or
electric shock.
▪ To reduce the risk of an electric shock, unplug the charg-
er from the power supply before attempting to clean it.
Removing the battery alone does not reduce the risk.
▪ Never attempt to connect two chargers together.
▪ Do not store or use the tool and battery pack in lo-
cations where the temperature may reach or exceed
104°F (40°C) such as alongside sheds, trailers or
metal structures during summer.
▪ The charger is designed for use from a standard
household electrical supply (230–240V). Do not at-
tempt to connect the charger to a supply with a dif-
ferent supply.
▪ If you wish to charge a second battery pack, unplug
the charger from the mains supply and leave it for at
least 15 minutes. After this time you can charge a sec-
ond battery pack.
▪ Under certain conditions, with the charger plugged in
to the power supply, the exposed charging contacts
inside the charger can be shorted by foreign material.
Foreign materials of a conductive nature such as, but
not limited to, steel wool, aluminium foil, or any build-
up of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cav-
ity. Unplug charger before attempting to clean.
▪ Do not freeze or immerse charger in water or any
other liquid.
VI - Additional instructions
for work with the
battery pack
▪ The battery pack for this tool has been shipped in a
low charge condition. You should charge the battery
pack fully before use.
WARNING: If the battery pack is cracked or
damaged in any other way, do not insert it in the char-
ger. There is a danger of electric shock.
▪ To ensure the longest battery life and best battery
performance, always charge the battery when the air
temperature is between 18–24°C. Do not charge the
battery pack when the temperature is below 0°C, or
above 40°C. This is important. Failure to observe this
safety rule could cause serious damage to the bat-
tery pack.
▪ The charger and battery pack may become warm to
6
EN
RS-754-1924-pages-BR2 10.8Li.indd 6
touch while charging. This is a normal condition, and
does not indicate a problem.
▪ To prevent overheating, do not charge battery packs
in direct sunlight in hot weather or near heat sources.
▪ Do not charge inside a box or container of any kind.
The battery must be placed in a well ventilated area
during charging.
▪ When the battery is defective, liquid can escape and
come into contact with adjacent components. Check
any parts concerned. Clean such parts or replace
them, if required.
▪ If the battery pack does not charge properly:
(1) Check current at receptacle by plugging in a lamp
or other appliance.
(2) Move charger and battery pack to a location where
the surrounding air temperature is approximately 65°F–
75°F (18°C–24°C).
(3) If charging problems persist, take or send the tool,
battery pack and charger to your local service centre.
▪ The battery pack should be recharged when it fails to
produce sufficient power on jobs, which were easily
done previously. DO NOT CONTINUE to use under
these conditions. Follow the charging procedure. The
Li- ion battery can be charged at any time without re-
ducing its service life. Interrupting the charging proce-
dure does not damage the battery.
▪ Do not incinerate the battery pack even if it is seriously
damaged or can no longer hold a charge. The battery
pack can explode in a fire.
▪ To facilitate the cooling of the battery pack after use,
avoid placing the charger or battery pack in a warm
environment such as in a metal shed, or an uninsu-
lated trailer.
WARNING: Never attempt to open the battery
pack for any reason. If the plastic housing of the bat-
tery pack breaks or cracks, return to a service centre
for recycling.
ReAD All Of tHe INstRUCtIONs IN tHe CHARG-
eR seCtION Of tHIs mANUAl befORe AttemPt-
ING tO CHARGe tHe bAtteRy PACK fOR yOUR
tOOl.
▪ Always use correct RS battery pack (the one supplied
with tool or a replacement pack exactly like it). Never
install any other battery pack. It will ruin your tool and
may create a hazardous condition.
▪ Charge battery packs only in RS chargers.
▪ Use an environmentally safe disposal unit at a munici-
pal waste disposal centre to dispose of a damaged or
worn out battery.
fIttING AND RemOvING tHe bAtteRy PACK
To remove the battery from the machine: press the bat-
tery release buttons (4) and take the battery out of the
tool.
WARNING: Always set the forward/reverse
switch (3) in central position before any work on the
machine e. g. fitting and removing a battery, changing
the bit,, transport, maintenance and storage.
754-1924
8.6.2012 . 15:09:08 .
T
o
s
b
▪
▪
▪
▪
C
▪
▪
D
m
d
▪
T
b
b
t
t
t
▪
▪
▪
b
T
t
(
D
t