Tabla de contenido
Idiomas disponibles
Idiomas disponibles
BASIC OPERATION OF COMMERCIAL WASHER
For additional information, see www.MaytagCommercialLaundry.com.
n
This tech sheet is not valid for models prior to series MAT14.
n
BASIC OPERATION OF COMMERCIAL WASHER
For additional information,
see www.MaytagCommercialLaundry.com.
This tech sheet is not valid for models prior to series MAT14.
IMPORTANT
IMPORTANT
Electrostatic Discharge (ESD)
Electrostatic Discharge (ESD)
Sensitive Electronics
Sensitive Electronics
ESD problems are present everywhere. ESD may damage
ESD problems are present everywhere. ESD may damage
or weaken the electronic control assembly. The new control
or weaken the electronic control assembly. The new control
assembly may appear to work well after repair is finished,
assembly may appear to work well after repair is finished,
but failure may occur at a later date due to ESD stress.
but failure may occur at a later date due to ESD stress.
Use an anti-static wrist strap. Connect wrist strap to green
Use an anti-static wrist strap. Connect wrist strap
n
ground connection point or unpainted metal in the washer.
to green ground connection point or unpainted metal
in the appliance
Touch your finger repeatedly to a green ground connection point
Touch your finger repeatedly to a green ground connection
or unpainted metal in the washer.
point or unpainted metal in the appliance.
Before removing the part from its package, touch the
Before removing the part from its package, touch the
anti-static bag to a green ground connection point or
n
antistatic bag to a green ground connection point or
unpainted metal in the washer.
unpainted metal in the appliance.
Avoid touching electronic parts or terminal contacts; handle
Avoid touching electronic parts or terminal contacts;
electronic control assembly by edges only.
n
handle electronic control assembly by edges only.
When repackaging failed electronic control assembly in
When repackaging failed electronic control assembly
anti-static bag, observe above instructions.
n
in antistatic bag, observe above instructions.
GENERAL USER INFORMATION
GENERAL USER INFORMATION
Blank Display
Blank display
This condition indicate the washer is inoperative. Enter set-up mode
This condition indicates the appliance is inoperative. Enter
to view diagnostic code.
set-up mode to view diagnostic code.
'0 Minutes' showing in display
"0 Minutes" showing in display
This condition indicates the washer cannot be operated. Coins
This condition indicates the appliance cannot be operated.
dropped or debit inputs during this condition will be stored in escrow
Coins dropped or debit inputs during this condition will be
but cannot be used until normal operation is restored by opening
stored in escrow but cannot be used until normal operation is
and closing the door. If a door switch fails, it must be replaced before
restored by opening and closing the door. If a door switch fails,
normal operation can be restored.
it must be replaced before normal operation can be restored.
Cold Start (initial first use)
Cold Start (initial first use)
Washer is programmed at the factory as follows:
Washer is programmed at the factory as follows:
11 minute wash period
11-minute wash period
n
1 rinses and 2 minutes of rinse agitation
1 rinse and 2 minutes of rinse agitation
n
$1.75 wash price (PD models)
$1.75 wash price (PD Models).
n
$0.00 wash price (PR models)
$0.00 wash price (PR Models).
n
Warm Start (after power failure)
After a delay of up to 8 seconds, the washer is restored to the
state that existed at time of the power failure.
ELECTRONIC CONTROLS SETUP
ELECTRONIC CONTROLS SETUP
-OR-
-OR-
Warm Start (after power failure)
After a delay of up to 8 seconds, the washer is restored to the
state that existed at time of the power failure.
Free Cycles
This is established by setting the cycle price to zero. When this
Free Cycles
happens, "SELECT CYCLE" will appear rather than a cycle price.
This is established by setting the cycle price to zero. When this
Debit Card Ready
happens, 'SELECT CYCLE' will appear rather than a cycle price.
This washer is debit card "cable" ready. It will accept a variety
Debit Card Ready
of debit card systems, but does NOT come with a debit card
This washer is debit card 'cable' ready. It will accept a variety
reader. Refer to the debit card reader manufacturer for proper
washer set-up. In models converted to a Generation 1 debit
of debit card systems, but does NOT come with a debit card reader.
Refer to the debit card reader manufacturer for proper washer
card system, debit pulses represent the equivalent of one coin
(coin 1).
set-up. In models converted to a Generation 1 debit card system,
debit pulses represent the equivalent of one coin (coin 1).
Display
Display
After the washer has been installed and plugged in, the display
After the washer has been installed and plugged in, the display will
will show "0 MINUTES." Once the washer has been plugged in
show '0 MINUTES'. Once the washer has been plugged in and the
and the washer door opened and closed, the display will show
washer door opened and closed, the display will show the price. In
the price. In washers set for free cycles, the display will flash
washers set for free cycles, the display will flash 'SELECT CYCLE'.
"SELECT CYCLE."
0
MINUTES
PRICE
2.00
9
Tabla de contenido
