Product Features - grupostayer IW 550 Manual De Instrucciones

gb
Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
Service
Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Use special care when working corners, sharp
edges, etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing have
a tendency to snag the rotating accessory and cause
loss of control or kickback.
Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control over the power tool.
Safety Warnings for Impact Wrenches
Hold power tool by insulated gripping surfaces
when performing an operation where the cutting
accessory or fastener may contact hidden wiring.
Cutting accessory and fasteners contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Use auxiliary handle(s), if supplied with the tool.
Loss of control can cause personal injury.
Hold the machine with a firm grip. High reaction
torque can briefly occur while driving in and loosening
screws.
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over the
power tool.
Never use the machine with a damaged cable. Do
not touch the damaged cable and pull the mains
plug when the cable is damaged while working.
Damaged cables increase the risk of an electric shock.
Products sold in GB only: Your product is fitted
with a BS 1363/A approved electric plug with internal
fuse (ASTA approved to BS 1362). If the plug is not
suitable for your socket outlets, it should be cut off and
an appropriate plug fitted in its place by an authorised
customer service agent.
The replacement plug should have the same fuse
rating as the original plug. The severed plug must
be disposed of to avoid a possible shock hazard
and should never be inserted into a mains socket
elsewhere.
Products sold in AUS and NZ only: Use a residual
current device (RCD) with a rated residual current of
30 mA or less.
PRODUCT DESCRIPTION AND PECIFICATIONS
Read all
instructions. Failure to follow the warnings
and instructions may result in electric
shock, fire and/or serious injury.
Intended Use The machine is intended for driving
in and loosening screws and bolts as well as for
tightening and loosening nuts within the respective
range of dimension.

PRODUCT FEATURES

The numbering of the product features refers to the
illustration of the machine on the graphics page.
1 Tool bit*
2 Tool holder
3 Handle (insulated gripping surface)
4 On/Off switch
*Accessories shown or described are not part of the
standard delivery scope of the product. A complete
overview of accessories can be found in our
accessories program.
MOUNTING
Change of useful
Before any manipulation of the power tool, remove the
mains plug from the socket.
When assembling the tool, make sure that it is firmly
attached to the tool holder. A tool that is not firmly
attached to its housing can become loose and make
you lose control over it.
- Insert the tool 1 on the square of the housing of tool
2.
OPERATION
Method of Operation
The tool holder 2 with the tool is driven by an electric
motor via a gear and impact mechanism.
The working procedure is divided into two phases:
Screwing in and tightening (impact mechanism in
action).
- 10 -
safety warnings and all