Tabla de contenido
Idiomas disponibles
Idiomas disponibles
ELECTRIC POWER
If the electrical circuit is overloaded with other appliances, your appliance may not operate
properly. It should be operated on a separate electrical circuit from other appliances.
Getting to Know your Skinnygirl 7-Piece Set
Product may vary slightly from illustration
Figure 1
1 Large Cup (13.5 oz)
Emulsifying Blade
Gasket Ring
Blade
Collar
Motor Base
Non-skid Feet
1 Travel Lid
1 Storage Lid
Spare Gasket Ring
1 Comfort Lip
1 Straw
Polarized Plug
6
Before Using for the First Time
1. Carefully unpack the Skinnygirl 7 piece Personal Blender Set and remove all packaging materials. Check
the contents to ensure that all parts and accessories are present, and have been received in good condition.
2. Handle the emulsifying blade attachment by the collar only.
WARNING: Do not touch blades. Blade attachments are very sharp. Use extreme care when handling.
Failure to do so can result in personal injury.
3. Wash all lids in warm, soapy water. Rinse and dry thoroughly.
4. Clean the cup before first use. Fill cup one-quarter full with clean, warm water.
Following the steps outlined in the Operating Instructions, pulse several times. Rinse thoroughly.
5. The motor base may be wiped with a damp cloth.
WARNING: DO NOT IMMERSE THE MOTOR BASE IN WATER.
Operating Instructions
1. Place the motor base on a flat, clean, dry countertop or table.
2. Make sure the unit is unplugged.
3. Place the food to be processed into the cup.
4. To assemble use the blade's collar to handle, place the emulsifying blade into the cup.
IMPORTANT: Check to make sure the comfort lip is not attached to the cup before assembling the blade.
If it is, simply lift off to remove.
IMPORTANT: In the base of the blade's collar, there is a plastic gasket seal that creates an airtight fit with the
Personal Blender's processing cup. After dishwashing and before each use, always check to make sure the
gasket is properly in place, as the heat from some dishwashers may cause the gasket to become loose.
WARNING: Never operate the Personal Blender when the processing cup is empty.
WARNING: Never overfill the processing cup. Do not exceed the MAX line.
5. Hold the cup firmly in one hand. Use the other hand to tighten the cup/blade assembly by turning the blade
collar clockwise until snug.
6. Plug the power cord into a 120V AC electrical outlet.
7
Invert the processing cup/blade assembly. Insert the cup assembled to the blade assembly into the motor
base, fitting the tabs into the slots on the motor base.
NOTE: The Personal Blender will not operate unless the 3 locking tabs on the blade collar are properly fitted
into the 3 slots on the motor base.
8. To process, turn the processing cup clockwise into the motor base and press down on the top of the cup.
The blender will operate until pressure is released.
WARNING: Do not operate the motor continuously for more than 1 minute at a time.
Allow the motor to rest for 3 minutes before continuing.
9. When processing is completed, turn the cup counter-clockwise in the base and lift to remove the cup/blade assembly.
10. Invert the cup/blade assembly. Hold the cup firmly in one hand. Use the other hand to turn the blade collar
counterclockwise and remove the blade from the processing cup.
11. Add the comfort lip to enjoy fresh juice, blended drinks or smoothies immediately.
Press down to fasten the comfort lip ring to the cup.
12. Unplug the Personal Blender when not in use and before cleaning.
WARNING: Never overfill the processing cup.
The maximum capacity of the cup is 13.5 oz./399 ml.
•
For best results, solid foods should not be larger than 1-inch pieces. Cut or tear food into pieces
approximately equal in size before processing.
WARNING: Always allow foods to cool at least one hour before processing in the personal blender.
7
Tabla de contenido
