Range Use; Cooktop Controls; Power Shutdown - Whirlpool LWF5050 Manual De Instrucciones, Instalación Y Uso

2. Turn on the oven burner as explained on section "Oven Burner" and "Model with electronic ignition thermostat". Remove the knob and
put it on a safe place.
3. Locate the flame adjustment screw in the thermostat
through the small perforation (see image), use a small
flat screwdriver to turn the screw until the flame is
around 1 cm tall.
4. When the flame is 1 cm tall, replace the knob and turn
it to the OFF position.
5. Replace the shelf on the bottom of the oven on its
original position.
6. Turn on the oven burner again and continue testing
the burner.
Oven Burner Flame
The different altitudes from the sea level, the variations on the gas supply line and the type gas conversion may cause the need to adjust
the primary air intake in the oven burner for an adequate air-gas blend, and therefore a better performance of the burner.
The oven burner flame should be blue colored and steady, follow these steps to adjust the flame:
1. Check the range is cold and all the cooktop burners are in the OFF position.
2. Unplug the range or turn off the power supply. Remove the shelf on the bottom of the
oven. Grab the shelf from both sides on the back part (see image below), pull out and
remove.
3. Locate the screw that holds the burner to the frontal range chassis and use a small
flat screwdriver to remove it. Place the screw in a safe place.
4. Hold the burner and pull it off to release the back part from the nozzle, try not to pull
the pigtail on the back if your range is equipped with electronic ignition.
5. To adjust the air, loose the air regulator screw located behind the burner and turn to open or close the air window (see image).
6. If the flame is yellow you need to open the window. When the flame is noisy or levitates our of the burner you need to slightly close the
window.
7. When the adjustment has been done, tighten the air regulator screw and set the burner to its original
position, align with the nozzle on the back and make sure the pigtail is set to the back of the range.
8. Place the screw with the washer holding the frontal range frame and the burner. Tighten the screw.
9. Connect the power cable or turn on the power supply.
10. Turn on the burner again following the steps on section "Testing your Range", "Oven Burner". If the
flame is steady and blue, the range is ready to use. Otherwise wait until the range is cold and return
to step 3.
11. When the oven burner has been adjusted and placed inside the oven, replace the bottom shelf to its
original location. Continue with the oven burner testing.
NOTE: Don't block the air outlet of the oven, don't wrap or cover the vents in the oven shelf.

Range Use

Cooktop Controls

The electronic ignition burners turn on the outer burner automatically when the knob is turned to Hi (High flame). See "Testing your Range",
"Cooktop Burners".
Before turning ON one of the burners, place the cookware with food over the cooktop. Don't turn on a burner
with an empty cookware or without it.
To set the burner temperature:
1. Push and turn the knob to the left. The burners will click but only the active burner will turn on.
2. Turn the knob to any position between Hi (maximum flame) and Low (minimum flame) or Hi (maximum
flame), Medium (medium flame) and (minimum flame). The click will stop.
Use this table to set the temperature levels.
Setting
Hi (max flame)
MED (medium flame)
Low (minimum flame)

Power Shutdown

In case of an extended power shutdown, the burners can be turned on manually.
Light up a match and hold it close from the burner that you want to use, turn the knob left to Hi position. After the burner is on, set the knob
to the desired setting.
14-Sep-2015 11:56:11 EDT | RELEASED
A. Location of thermostat
B. Location of flame adjustment screw
C. Flame adjustment screw
Recommended use
 Start cooking food.

Boil liquids.

Keep a quick boiling.

Deeply fry food.

Fry food lightly.

Cook soups and sauces.

Steam or cook food.

Keep the food warm.

Simmer food.
In some European factories the letter "W" of the part code mentioned herein will be automatically
replaced by the number "4000" (e.g. "W12345678" becomes "400012345678")
A. Oven burner
B. Screw
C. Air regulator
22