Idiomas disponibles
Idiomas disponibles
Intended use
The tool is intended for the sanding of large surface of
wood, plastic and metal materials as well as painted
surfaces.
Noise
The typical A-weighted noise level determined accord-
ing to EN62841-2-4:
Model
Sound pressure
level (L
BO005CG
BO006CG
The noise level under working may exceed 80 dB (A).
NOTE: The declared noise emission value(s) has
been measured in accordance with a standard test
method and may be used for comparing one tool with
another.
NOTE: The declared noise emission value(s)
may also be used in a preliminary assessment of
exposure.
WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared
value(s) depending on the ways in which the
tool is used especially what kind of workpiece is
processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Vibration
The vibration total value (tri-axial vector sum) deter-
mined according to EN62841-2-4:
Work mode: sanding metal plate
Model
Vibration emis-
sion (a
BO005CG
BO006CG
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
Uncertainty (K) :
) : (dB(A))
(dB(A))
pA
73
3
76
3
Uncertainty (K) :
2
2
,
) : (m/s
)
(m/s
)
h
AG
2.6
1.5
2.6
1.5
WARNING:
The vibration emission during
actual use of the power tool can differ from the
declared value(s) depending on the ways in which
the tool is used especially what kind of workpiece
is processed.
WARNING:
Be sure to identify safety mea-
sures to protect the operator that are based on an
estimation of exposure in the actual conditions of
use (taking account of all parts of the operating
cycle such as the times when the tool is switched
off and when it is running idle in addition to the
trigger time).
Declarations of Conformity
For European countries only
The Declarations of conformity are included in Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING
Read all safety warnings, instruc-
tions, illustrations and specifications provided with
this power tool. Failure to follow all instructions listed
below may result in electric shock, fire and/or serious
injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Sander safety warnings
1.
Always use safety glasses or goggles.
Ordinary eye or sun glasses are NOT safety
glasses.
2.
Hold the tool firmly.
3.
Do not leave the tool running. Operate the tool
only when hand-held.
4.
This tool has not been waterproofed, so do not
use water on the workpiece surface.
Ventilate your work area adequately when you
5.
perform sanding operations.
6.
Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
Use of this tool to sand some products, paints
7.
and wood could expose user to dust contain-
ing hazardous substances. Use appropriate
respiratory protection.
Be sure that there are no cracks or breakage
8.
on the pad before use. Cracks or breakage
may cause a personal injury.
Watch your footing and maintain your balance
9.
with the tool. Make sure there is no one below
when working in high locations. Dropping your
9 ENGLISH
