Idiomas disponibles
Idiomas disponibles
5.3 Trial run for new diamond cutting wheels
Have the equipment run in idle mode for at least
1 minute with the cutting wheels fi tted. Replace
vibrating wheels immediately.
6. Operation
6.1 Charging the Li battery pack (Fig. 4-5)
1. Remove the battery pack (b) from the handle,
pressing the pushlock button (c) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(d) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
Anl_TP-MA_36-30_Li_BL_SPK13.indb 17
Anl_TP-MA_36-30_Li_BL_SPK13.indb 17
GB
6.2 Battery capacity indicator (Fig. 6)
Press the battery capacity indicator switch (f). The
battery capacity indicator (e) shows the charge
status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6.3 Switch (Fig. 7)
The equipment comes with a safety switch which
is designed to prevent accidents.
To start the equipment, push the locking lever (5)
forwards and then press the On/Off switch (4).
Warning! Wait until the machine has reached
its top speed.
6.4 Changing and setting the diamond
cutting wheels (Fig. 8-11)
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Removing:
•
Undo the locking screw for the depth stop (6)
and remove (Fig. 8)
•
Swing the depth stop (7) downwards (Fig. 9)
•
Slacken the screw for the flange cover (11)
and open the flange cover (12) (Fig. 9)
•
Press and hold the spindle lock (2) and undo
the socket head screw (h) with the supplied
hex key (13) (Fig. 10)
•
Remove the following as shown in Fig. 11:
- the outer flange (a)
- the top cutting wheel (b)
- the top inner flange (c)
- 6x spacers (d)
- the bottom cutting wheel (e)
- the bottom inner flange (f)
- 17 -
29.05.2024 08:37:20
29.05.2024 08:37:20
