Idiomas disponibles
Idiomas disponibles
Touring Series
INTRODUCTION
Thank you for purchasing the NanoAmp6-BT. The NanoAmp6-BT uses a
STMicroelectronics TDA7498E Audio Amplifier for amazing performance
and clarity with superb power handling and efficiency. Built-in thermal
overload and short-circuit protection combined with the selection of only
the highest quality components ensures your NanoAmp6-BT will provide
you with years and years of audiophile quality listening enjoyment. Your
NanoAmp6-BT includes RCA Left/Right line level inputs found on the rear of
the amplifier. lf your device does not have a RCA Left/Right output you can
use an adapter cable such as a 3.5mm to RCA Cable or other line level
cables that meet your source device's type of output. The NanoAmp6-BT
includes Bluetooth streaming audio. Use the Bluetooth aptX connection to
wirelessly stream audio from your iPhone, Android smartphone, tablet, or
laptop. The aptX code produces better quality sound than standard
Bluetooth when used with aptX compatible devices. lncluded with your
NanoAmp6-BT is a 36VDC power supply that provides the power for your
NanoAmp6-BT to fill any room with quality sound and performance.
CONNECTING SPEAKERS
The NanoAmp6-BT features binding posts for more convenient speaker
connection. These binding posts will accept bare wire, 3/8" spade terminals,
or standard banana plugs. Note: The binding posts will accommodate dual
banana plugs.
USING LINE LEVEL INPUT
Many portable music players use a 3.5mm jack to play music through
headphones. Connect a 3.5mm to RCA cable between the source
headphone out and the amplifier's line input. lf the source device is not
portable il likely uses RCA stereo cables. Connect a stereo audio cable from
the source device to the amplifier's line input.
USING THE BLUETOOTH CONNECTION
The Bluetooth audio source device must be paired and connected to the
NanoAmp6-BT to play music wirelessly from your phone, tablet, or other
music player.
www.stsproaudio.com
NanoAmp-BT
160W+160W Stereo Amplifier
Class D - Bluetooth APTX
AMPLIFIER
Turn the power switch to "Off"
Set the select switch to "Bluetooth"
Turn the power switch to "On"
MOBILE DEVICE
On your mobile device select "HiFi" from available devices to pair the
devices.
From "Paired Devices" list select "HiFi"
Under "Settings", select "Use for media audio"
The NanoAmp6-BT will emit a beep to let you know that the mobile device
is paired and selected. Adjust the output level of the mobile device to
approximately 75% for best sound quality and adjust the master volume on
the amplifier to set the ideal listening level.
NOTE
It is normal for some Bluetooth devices to require a little more time to pair
Bluetooth with your NanoAmp6-BT. If you have trouble pairing and
connecting to the amplifier, simply repeat all of these steps for the amplifier
and mobile device several times until you have a successful pairing. Your
Bluetooth enabled device should remember the NanoAmp6-BT in the future
and not require this procedure again.
OPERATION
Connect 4-8 Ohm speakers to the binding posts
Plug the power supply into the amplifier then into the wall outlet.
LINE LEVEL IN: Connect a line-level device to the RCA inputs and set input
to "AUDIO IN"
BLUETOOTH: Turn on the amplifier, set the input switch to "BLUETOOTH",
and follow pairing instructions.
Adjust the volume to the desired listening level
CAUTION
For indoor use only. Your NanoAmp6-BT should not be exposed to any
outdoor elements including dust, water, moisture, humidity,
temperatures outside normal living conditions. There are no
serviceable parts inside your amplifier, therefore do not open your
NanoAmp6-BT or it will void your warranty. For optimum life, place it in
a location that is open and where air can fully circulate. Use a clean cloth
to dust your NanoAmp6-BT. Your amplifier comes with a compatible
power supply. lf an inappropriate power supply is used and the unit is
damaged the warranty will be voided.
Power Output (10% THD):
Amplifier Efficiency:
Minimum THD:
Signal-to-noise Ratio:
Signal-to-noise Ratio:
Bluetooth Compatibility:
DC Power Input Jack:
Power Requirements:
Included Power Supply:
Dimensions:
TECHNICAL SPECIFICATIONS
Owner's Manual - 2020
2 x 160 watts into 4 ohm
2 x 100 watts into 8 ohm
>90%
<1%
>90dB
20-20.000Hz
v4.0
2,5 mm x 5,5 mm
18 a 36 VCC, 4.5 A
110-240VAC, 36VDC, 4.5A
114,3 mm W
177,8 mm H
31,8 mm D
facebook.com/stsproaudio
or
user
