Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
PACKAGE CONTENTS
A – Post Light x 1
B–Male Plug x 1 (with 60 in. wire)
D – Small
Adaptor x 1
E – Wire Connector (with 39 in. wire) x 1
Assembly and Installation
1
Select the appropriate adaptor
Post light with small adaptor:
The post light (A) comes pre-attached to the small hardscape adaptor
□
(D). If you select the small adaptor, you can directly install it in the next
step.
Post light with large adaptor:
Use a screwdriver (sold separately) to press in the button (1), and then
□
pull the post light (A) up by hand.
Place the post light (A) over the large adaptor (C), until the button (1)
□
insert to the hole of the post light (A).
NOTE: There have a plastic gasket around each button (1). Please do
not remove the plastic gasket when replacing the adapter.
LOW VOLTAGE LED POST LIGHT
Adaptor x 1
C –Large
AA – Self-Threading Screw (30 mm) x 2
F –Female Plug x 1
BB – Plastic Anchor (25 mm) x 2
Installing the post light on the post when the
2
wire behind the post
Use at least a 7/16 in. drill bit to drill a hole on the mounting
□
surface large enough for the male plug (B) to pass through the
hole on the mounting surface.
Insert the male plug (B) through the hole on the mounting
□
surface.
Insert the male plug (B) into the female plug (F).
□
Place the adaptor (C/D) over the top of the post, use a pencil
□
(sold separately) to gently mark the location of the two holes
on the wall.
Remove the adaptor (C/D) from the post. Use a drill to bore two
□
5 mm deep holes in the wall, placing the holes following the
location of the two holes on the adaptor (C/D).
Insert the plastic anchors (BB) into the holes on the wall, screw
□
the self-threading screws (AA) into the plastic anchors (BB) to
fix the adaptor (C/D) on the post.
1
Item # 1008 540 723
Model # HSP1801LX-02/MB
Item # 1008 540 729
Model # HSP1801LX-02/ZC
Use and Care Guide
Manuales relacionados para HAMPTON BAY HSP1801LX-02/MB
Resumen de contenidos para HAMPTON BAY HSP1801LX-02/MB
- Página 1 Item # 1008 540 723 Model # HSP1801LX-02/MB Item # 1008 540 729 Model # HSP1801LX-02/ZC Use and Care Guide LOW VOLTAGE LED POST LIGHT PACKAGE CONTENTS Adaptor x 1 A – Post Light x 1 B–Male Plug x 1 (with 60 in. wire) C –Large...
- Página 2 Assembly and Installation (continued) Installing the post light on the post when the wire Connecting the wires and applying caulk beside the post Use a pliers to clamp off the (1) part of the adaptor (C/D) so that the male □...
- Página 3 Care and Cleaning □ □ Clean the fixture with a soft dry cloth. Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem Possible Cause Solution □ □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. The fixture will There is no power.
- Página 4 Artículo # 1008 540 723 Modelo # HSP1801LX-02/MB Artículo # 1008 540 729 Modelo # HSP1801LX-02/ZC GUÍA DE USO Y MANTENIMIENTO LUZ DE COLUMNA LED DE BAJO VOLTAJE CONTENIDO DEL PAQUETE A –Luz de Columna x1 C – Grandes Adaptador x 1 F –...
- Página 5 Montaje e Instalación (continuación) Instalar la luz de la columna en la columna cuando el Conexión de los cables y aplicar relleno de cable al lado de los columna costura Sujetar la parte (1) del adaptador (C/D) con pinzas para que el enchufe □...
- Página 6 Mantenimiento y Limpieza □ □ Limpia la lámpara con un paño suave y seco. No uses limpiadores con químicos, solvents, o productos abrasivos. Solución de Problemas Problema Causa Posible Solución □ □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito El accesorio no No hay corriente.
- Página 7 FCC Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.