Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
PACKAGE CONTENTS
A – Lamp Body x1
Assembly and Installation
1
Attaching and installing the light
WARNING: Never use a hammer to insert the light into the ground.
Insert the fixture wire on the wire connector (C) into the groove located
□
on the top of the ground stake (B).
Screw the ground stake (B) into the lamp body (A). Ensure the fixture
□
wire on the wire connector (C) stays in the center of the groove of the
ground stake (B) to avoid damage to the fixture wire.
Prepare a hole in the installation location. Use a tool such as a
□
screwdriver to prepare the installation hole to ensure that the hole is
not larger than the ground stake (B).
Install the ground stake (B) in the ground by pushing on the lamp body
□
(A).
B – Ground Stake (6.5 in.) x1
LED LOW VOLTAGE PATH LIGHT
C – Wire Connector (with 12 in. wire attached to lamp body) x1
2
Connecting the wires
WARNING: The wire connector (C) contacts have sharp edges for
piercing the main low voltage cable. To avoid injury, do not touch
the metal contacts.
CAUTION: The wire from low voltage power unit should be 12-16
AWG type underground low Energy Circuit Cable.
IMPORTANT:
Protect the wiring by routing it in close proximity to the light
□
fitting, or next to a building structure such as a house or a
deck.
The landscape wire and connector can also be hidden under
□
stone or buried under grass at a maximum depth of 6 in. (15.24
cm).
Do not install the fixture within 10 ft. of a pool, spa, or fountain.
□
Do not submerge the fixture in water.
□
Place the wire connector (C) on opposite sides of the low voltage
□
cable (not included) from the transformer (not included) where the
fixture will be located.
Align and fit the main low voltage cable vertically to the slot of the
□
wire connector (C).
Press the wire connector (C) together until it is locked around the
□
main low voltage cable. The pre-set prongs will pierce the cable
insulation and establish contact with the electrical wire inside.
Once the wire connector (C) is in place, it is recommended to
□
wrap it with electrical tape (not included).
After all fixtures are installed, turn on the transformer.
□
1
Item #1008 454 051
Model # JAO1501L-2/BR
Item #1008 454 055
Model # JAO1501L-2/CP
Item #1008 454 049
Model # JAO1501L-2/AL
Use and Care Guide
Manuales relacionados para Home Decorators Collection JAO1501L-2/BR
Resumen de contenidos para Home Decorators Collection JAO1501L-2/BR
- Página 1 Item #1008 454 051 Model # JAO1501L-2/BR Item #1008 454 055 Model # JAO1501L-2/CP Item #1008 454 049 Model # JAO1501L-2/AL Use and Care Guide LED LOW VOLTAGE PATH LIGHT PACKAGE CONTENTS A – Lamp Body x1 B – Ground Stake (6.5 in.) x1 C –...
- Página 2 Care and Cleaning □ □ Clean the fixture with a soft dry cloth. Do not use any cleaners with chemicals, solvents or harsh abrasives. Troubleshooting Problem Possible Cause Solution □ □ Check the outlet and ensure that a breaker or GFCI circuit has not been tripped. The fixture will There is no power.
- Página 3 Artículo #1008 454 051 Modelo # JAO1501L-2/BR Artículo #1008 454 055 Modelo # JAO1501L-2/CP Artículo #1008 454 049 Modelo # JAO1501L-2AL GUÍA DE USO Y MANTENIMIENTO LAMPARA PARA SENDAS CON LED DE BAJO VOLTAJE CONTENIDO DEL PAQUETE A – Estructura de la Lámpara x1 B –...
- Página 4 Mantenimiento y Limpieza □ □ Limpia la lámpara con un paño suave y seco. No uses limpiadores con químicos, solvents, o productos abrasivos. Solición de Problemas Problema Causa Posible Solución □ □ Verifique el tomacorriente y asegúrese que no esté apagado el interruptor o circuito El accesorio no No hay corriente.
- Página 5 FCC Warning Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.