Idiomas disponibles
Idiomas disponibles
EN
ST17BN, ST22BN, ST25BN, ST51BN, ST75BN, ST145BN
Please read these safety instructions before use and
keep them carefully.
Battery safety instructions
If the battery is swallowed, seek medical attention
immediately.
Follow the instructions in the manual when replacing
the batteries. Use only the correct type of batteries.
Do not let children change the batteries.
Store batteries away from metal objects, in a cool, dry
place, out of direct sunlight. Do not artificially short-
circuit the batteries.
Remove the batteries when not using the device for
a long time.
Never dispose of batteries in fire.
Do not revive dead batteries by heating or otherwise.
USE AND OPERATION
Unlocking the safe:
Dial the password-code 159, each press is confirmed
by a sound tone. The password is set at the factory
and is used for the first unlocking. Then press the E
BUTTON (bottom right of the keyboard) and turn the
wheel to the right - safe lock. The safe is unlocked.
Programming a lock opened using a numerical code
1. Unlock and open the safe.
2. Locate the red one located on the inside of the
door next to the hinge.
3. Press the red button. When you hear a beep,
release the button. Choose 3 to 8 digits to use as
a numeric code. For security reasons, we strongly
recommend choosing a code with at least 3-4 digits.
Press the appropriate number buttons and confirm
the code by pressing the E button. Write down the
numeric code in case you forget it.
4. Unlocking the safe: press the numeric code buttons
and then the E button. Turn the wheel. The safe is
unlocked.
5. When you press the full code button, you have 5
seconds to open the safe. After 5 seconds, the safe
will automatically lock again. To open it again,
press the numeric code buttons again.
If you enter an incorrect number, press "C" to cancel
it.
Note: Each time you press a number, the yellow light
will flash and you will hear a beep, which indicates
microprocessor confirmation. If the yellow light does
not stop flashing and beeping, it means that the
code is incorrect. Entering the code incorrectly three
times will cause the microprocessor to refuse to
accept input for 20 seconds. Even then, if you enter
the wrong code three times, the microprocessor will
refuse entry for 5 minutes.
Electronic security box with identification code lock
17
Battery replacement
Unlock the safe using the numeric code and turn the
. Slide the lid off the battery compartment located on
the back of the door. Replace the dead batteries with
new batteries of the same type and slide the cap back
into place.
Be careful not to damage the electrical installation
when replacing dead batteries.
Hand over used batteries to a small chemical waste
collection point.
Low battery warning light
If the batteries are low, the red light will immediately
come on. It means that you have to replace the
batteries within one to two months.
Unlocking the safe without a numerical code
For your convenience, a device is installed in the
safe that allows you to unlock the safe without using
a numerical code. For example, if you forget your
numerical code, remove the descriptive label located
on the front in the middle. Behind the label you will
find a mechanism that blocks the door.
The key must first be pushed slightly by 2-3 mm, then
turned to the left by 60°. turn 90° to the right.
This way you can always unlock the safe.
Never keep safe keys inside the safe. The batteries
may run out and the ability to open the safe may be
lost.
WARNING !!!
According to the EN 1143-1 standard, the furniture
safe is not included in any security class.
CLEANING AND MAINTENANCE
Never use chemical cleaners to clean your safe. Wipe
it with a dry cloth.
Never clean any part of the safe with a hard, sharp or
abrasive object.
Storage when not in use for a long time
- If possible, store the safe in a place with constant
temperature and humidity, never in a place where the
temperature is high.
TECHNICAL DATA ST17BN
External dimensions 230x170x170 mm
Internal dimensions 226x120x166 mm
Door/shell thickness 3/1 mm
Weight 3.0 kg
TECHNICAL DATA ST22BN
External dimensions 340x180x220 mm
Internal dimensions 335x130x215 mm
Door/shell thickness 3/1.5 mm
