ESG 105RMCCFM
1
2
ERROR CODE:
****
3
BT
4a
USER SELECT: 1
REMOTE CONTROL
4b
USER SELECT: 2
Double Click
3 sec.
4c
CURRENT USER: 2
Double Click
Klauke i-press
Klauke i-press
www.klauke.com/connectivity
www.klauke.com/connectivity
Klauke i-press
Klauke i-press
For US and Canada only
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée
aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le foncti-
onnement.
NOTICE:
Changes or modifi cations made to this equipment not expressly approved by Klauke may void the FCC authorization to operate this equipment.
HE.19142_D © 04/2020
Error code
*1
*2
Bluetooth (if connected)
Battery charging level
initial settings:
to change:
current user confi rmed
additional profi les:
1: remote control (double click)
2: double click
3: double click
4: double click
5: double click
®
®
Software
Software
®
®
App
App
WORK
SERVICE
5
NEXT
SERVICE:
9826 OP
6
TOTAL:
t = 0
07
.
Q = 21
12 Ah
.
n = 174
7
*1 Error codes:
1 Überstromsicherung
1 Overcurrent fuse
2
Überstromsicherung durch Komparator
2 Overcurrent comparator
3 Boardtemperatur zu hoch
3 Overheat board
4
Akkutemperatur zu hoch
4 Overheat battery
5
Akkuspannung zu gering
5 Battery empty, operation stop
6
Fehlpressung bei laufendem Motor
6 Faulty crimp motor in operation
7
Fehlpressung bei stehendem Motor
7 Faulty crimp motor not in operation
8
Niedrige Akkuspannung
8 Low battery
9 Akku leer
9 Battery empty
10
RTC-Batterie leer
10 RTC battery low
12 Service nötig
12 Service necessary
13 RTC nicht verfügbar
13 RTC not found
14
BT-Modul nicht verfügbar
14 BT unit not found
15 Modul nicht verfügbar
15 Mobile unit not found
16
Drucksensor nicht verfügbar
16 Pressure sensor not found
17
Berstdruck überschritten
17 Burst pressure exceeded
18
Akkutemperatur zu gering
18 Battery temperature too low
19 Batteriereserven zu gering
19 Battery reserves
20 Überstromsicherung (I)
20 Overcurrent fuse (I)
21 Fernbedienung-Batterie schwach
21 Remote Control Battery Low!
22 Service notwendig SAST1
22 Service necessary SAST1
23 Service notwendig SAST2
23 Service necessary SAST2
24 Service notwendig SAST3
24 Service necessary SAST3
25 Remote-Modus: Werkzeug-Taster nicht betätigt
25 Remote mode: tool trigger not actuated
27 Motortemperatur zu hoch
27 Overheat motor
28 Service notwendig: Druck niedrig
28 Service necessary: Pressure low
29 Service notwendig: Druck hoch
29 Service necessary: Pressure high
*2
≤ 20 sec.
≤ 20 sec.
> 20 sec.
> 20 sec.
≤ 20 sec.
≤ 20 sec.
REPEAT
REPEAT
DON´T DO
Cycles
(until next service)
s
Since manufacturing:
operating houres
h
Capacity
# crimps
(2Hz)
General
safety rules
VIII
