cecotec CONGA ROCKSTAR 3000 ADVANCE ERGOWET CONNECTED IA Manual De Instrucciones página 26

ENGLISH
5. WATERTANK ACCESSORY
- Do not use cleaning agents. Use clean and room temperature water only. Do not use the
vacuum cleaner to vacuum water.
- When the vacuum cleaner is not going to be used for a long period of time, remove the
water tank and empty the remaining water. Do not expose it to direct sunlight or to damp
environments.
Mop installation
- Place the mop cloth on the ground with the Velcro facing upwards.
- Align the mop cloth with the Velcro strips on the water tank and attach it without covering
the wheels. Fig. 14
Replacing the mop
- Remove the water tank from the vacuum cleaner.
- Use your foot to hold the accessory against the ground and pull the vacuum cleaner
upwards until both parts are separated.
- Replace the mop and refill the water tank.
- Install the water tank again, insert the tank in the lower part of the vacuuming brush head,
and press until it is fixed.
Water emission
- When using this product for the first time, make sure the water tank lid is not fully open.
- When the product is not in use, check that the water release button and cap are closed, as
the product may continue to let out water if the water tank is full.
- To activate the water emission, the water emission push button must be pressed, and to
stop the water emission, the push button must be in the original position, as shown in
figure 15.
6. CLEANING AND MAINTENANCE
- Turn the appliance off, unplug it from the power socket, and allow it to cool down before
cleaning it.
- Use a soft, slightly dampened cloth to clean the device's surface.
- Never immerse the device in water or other liquids. Do not allow liquids to enter the device.
- Do not use sponges, powder products, or abrasive cleaning agents to clean the product.
- Do not leave the vacuum cleaner in a place with direct sunlight.
- Do not leave the vacuum cleaner in a wet place after cleaning it.
- After the brush has been used for a long time, bristles might start to tangle with hair and
other particles. Clean it for it to operate correctly again.
50
Filters and tank cleaning
- To prevent the appliance from overheating and losing suction power, it is suggested to
clean the filters frequently. To make the most of the suction power, it is suggested to clean
the filter after every use.
- The filters shelf life will depend on the accumulated use and the type of particles which are
frequently vacuumed. It is recommended to replace the filters every 6 months.
- To remove the filters (Fig. 16):
1. Press the dust-tank opening button, marked with the word "CLEAN", and pull on the
metallic handle to remove the filtering system.
2. Once the filtering system is out, turn the metallic handle anticlockwise and you will be
able to take the high-efficiency filters out.
- Vacuum and shake the filters to remove every particle and dust remain that may block
them and difficult the correct air circulation. Remember not to use the vacuum cleaner
without the filters properly assembled.
- Filters cannot be washed inside a washing machine nor dried with a hair dryer.
- Do not brush the high-efficiency filter.
- To empty the dust tank, press the dust tank lower-cover opening button, open it and empty
it. Fig. 17
Cleaning the Jaliscazo brush
Fig. 18
- Move the rotary brush release button with the finger toward the arrow and remove the
cover on the same side of the brush.
- Take one end of the brush out as shown on the image.
- It is important to clear and clean all the residues left in the brush rotary axis.
- If you decide to wash the brush, you must air dry all the pieces. Assemble the pieces back
to use the brush again.
Watertank cleaning
- To clean the water tank, fill it with clean water, shake it, and empty it.
- The mop is washable; therefore, it is suggested to wash it after every use.
- Replace the cloth after 20-30 uses, depending on the use.
- When the mop cloth is used for a long time, it is possible that the water output is affected.
This can be avoided by cleaning both the mop and water tank regularly.
How to remove the battery
Press the battery release button and remove the battery as shown in figure 19. Store the
battery in a plastic bag and leave it in a dry place.
Vacuum cleaner storage
If the robot will not be used for a long period of time, remove the battery from the product, and
store it in a dry and safe place.
CONGA ROCKSTAR 3000 ADVANCE ERGOWET CONNECTED IA
ENGLISH
51