cecotec CONGA ROCKSTAR 1700 X-TREME ERGOWET Manual De Instrucciones página 24

ENGLISH
Charge and display
- When the battery percentage is 20 % or below, the device will automatically enter the
low consumption mode. It is recommended to charge the device when it reaches this
percentage.
- During charging, the charge light indicator will turn on red and the display will show the
current charge percentage. When the device is fully charged, the battery indicator will turn
green and the display will show 100%. Fig. 5
- You can charge the battery when the battery is installed or not in the device. Connect the
adapter and connect the other end to the battery, paying attention to the direction. Once it
is properly connected, the charge light indicator will turn on red and will turn green once
the charge is complete. Fig. 6-7
5. WATER TANK ACCESSORY
- Do not use cleaning agents. Use clean and room temperature water only. Do not use the
vacuum cleaner to vacuum water.
- When the vacuum cleaner is not going to be used for a long time, please remove the
water tank and empty the remaining water. Do not expose it to direct sunlight or to damp
environments.
Mop installation
- Place the mop cloth on the ground with the Velcro facing upwards.
- Align the mop cloth with the Velcro strips on the water tank and attach it without covering
the wheels. Fig. 8
Replacing the mop
- Remove the water tank from the device.
- Use your foot to hold the accessory against the ground and pull the vacuum cleaner
upwards until both parts are separated.
- Replace the mop and refill the water tank.
- Install the water tank again, insert the tank in the lower part of the vacuuming brush head
and press until it is fixed.
Water emission
- When using the vacuum cleaner, make sure that the water tank cap is completely closed.
- When you are not using the vacuum cleaner, check that the water emission button and the
cap are closed as the vacuum cleaner may still emit water if the water tank is full.
- To activate the water emission, the water emission push button must be pressed, and to
stop the water emission, the push button must be in the original position, as shown in
figure 9.
46
6. CLEANING AND MAINTENANCE
- Turn the appliance off, unplug it from the power socket and allow it to cool down before
cleaning it.
- Use a soft, slightly dampened cloth to clean the device's surface.
- Never immerse the device in water or other liquids, do not allow liquids to enter the device.
- Do not use sponges, powder products or abrasive cleaning agents to clean the product.
- Do not leave the device in a place with direct sunlight.
- Do not leave the device in a wet place after cleaning it.
- After the brush has been used for a long time, bristles might start to tangle with hair and
other particles. Clean it in order for it to operate correctly again.
Filters and tank cleaning
- To avoid the appliance from overheating and losing suction power, it is suggested to clean
the filters frequently. To make the most of the suction power, it is suggested to clean the
filter after every use.
- The filters shelf life will depend on the accumulated use and the type of particles which are
frequently vacuumed. It is recommended to replace the filters every 6 months.
- To remove the filters (Fig. 10):
1. Press the dust tank opening button, marked with the word "CLEAN", and pull on the
metallic handle to remove the filtering system.
2. Once the filtering system is out, turn the metallic handle anticlockwise and you will be
able to take the high efficiency filters out.
- Vacuum and shake the filters to remove every particle and dust remain that may block
them and difficult the correct air circulation. Remember not to use the vacuum cleaner
without the filters properly assembled.
- Filters cannot be washed inside a washing machine nor dried with a hair dryer.
- Do not brush the high-efficiency filter.
- To empty the dust tank, press the dust tank lower cover opening button, open it and empty
it. Fig. 11
Cleaning the Jaliscazo brush
Fig. 12
1. Move the rotary brush release button with the finger toward the arrow and remove the
cover of one of the ends of the brush.
2. Take one end of the brush out as shown on the image.
- It is important to clear and clean all the residues left in the brush rotary axes.
- If you decide to wash the brush, you must air dry all the pieces. Assemble the parts in
reverse order of disassembly so that the brush can be used again.
ENGLISH
CONGA ROCKSTAR 1700 X-TREME ERGOWET 47