Idiomas disponibles
Idiomas disponibles
GETTING STARTED
The objectives have already been placed in the nose piece in the right sequence. They
are parfocal and parcentered. Unless necessary, do not remove the objectives. Insert the
plug into an earthed power point (check if the voltage matches the microscope). Switch
on the light. The microscope is now ready for use.
POWER OPTIONS
• Main power cable (100...240V~/50Hz), available for EU (item no. 76995), UK (item no.
76999), CH (item no. 76998) and USA (item no. 76996).
• Rechargeable batteries (AA, 1,5V), optional item, can be ordered as a pack of three
(item no. 29554). When this battery pack is placed, it will be charged automatically when
the microscope is connected to the mains and the power switch of the microscope is
switched on. When the LED indicator, located on the back of the microscope, is green,
the battery pack is fully charged. The microscope can now be used, disconnected from
the mains, for 10 hours. When the LED indicator is red, the batteries need to be charged
again. Charging time is about 3 hours.
• Non rechargeable batteries (AA 1,5V, 3 pieces). The microscope will also work with
these batteries. WARNING: do not connect the microscope to the main electricity when
these batteries are placed. This will cause severe damage to the microscope.
DOUBLE SAFETY IS GUARANTEED
• Full separation from the main power through DPDT switch.
• Indicator LED to show if main power is switched on and if optional battery is charged.
• Potentiometer for regulation of the High Power LED.
• High Power LED for bright image.
• DPDT (double pole, double throw) when switched off, the power is completely shut off.
The BMS 100 FL microscope has a LED illumination light source. This light source is
characterized by low maintenance and low power consumption. This LED source has an
average life span of 50,000 hours. Besides that, this LED illumination system lacks heat
development and is therefore safe to be used by children. It is recommended though that
an adult is supervising at all time.
SAFETY INFORMATION
• Think of the safety of yourself and those being around you.
• Always disconnect mains plug from power point before maintenance.
• Work in a clean and proper environment.
• Clean all parts coming in contact with the observed specimen to prevent infection.
• Place the microscope on a sturdy, level table or working surface.
• Always use original accessories.
CAUTION
The delicate components may get damaged if the microscope is not handled with care.
Use the microscope in a clean environment. Do not use it when it is subject to direct
sunlight, high temperatures, humidity or dust. Carry the microscope with care, do not
hold it by the stage. Remove specimen before transport.
REPLACING FUSE
Always disconnect mains plug from the power point before any kind of maintenance.
The BMS 100 FL microscope is equipped with one glass fuse, 1,0 A (applicable for item
2760611)
• Wait until the microscope and electrical parts have cooled down.
• The fuse is located at the back of the microscope.
• Open the housing of the fuse by turning it counter clockwise.
• Take broken fuse out.
• Replace new fuse after being sure of using same rating in new fuse.
• Screw fuse holder clockwise back in place.
CARE & MAINTENANCE
• Microscope is a precision instrument, it should be handled with care.
• The microscope should not be in direct sunlight. But placed in a dry and clean place.
• Avoid high temperature and vibration.
• Avoid dirt and fingerprints on the lens surface, this way your image will not be affected.
• All lenses must be kept clean. Fine dust on the surface of the lens should be blown off
with hand blower or wiped off gently with a soft lens tissue. Fingerprints or oil mark on it
should be wiped off with a tissue moistened with a small amount of xylene or a mixture
of alcohol and ether.
• Never use the organic solution to clean the other surface (especially the plastic
surfaces). If necessary, please choose the neutral detergent.
• All lenses are mechanically structured and adjusted to the best state for the
microscope, please do not disassemble.
• The rack and pinion should be regularly greased with a small amount.
• After use, cover the microscope with the provided dust cover and store it in a dry and
clean place, that is free from moisture to prevent rust.
SPECIFICATIONS
For more specifications, please view the product page on the website:
www.bmsmicroscopes.com
It is within our company policy to develop continuously. BMS Microscopes b.v. reserves
the right to change design and specifications without further notice.
BMS Microscopes b.v.
Essebaan 50
2908 LK Capelle aan den IJssel
The Netherlands
Tel.: +31(0)10 458 42 22
E-mail: [email protected]
Environment protection first!
Your appliance contains valuable materials which can be recovered
or recycled. Leave it at a local civic waste collection point.
