Switch
Built-in, leaf-type, non-locking, push-to-talk
Shock Mount
Internal rubber vibration isolator
Cable
Highly durable cable with effective hum shielding, four conduc-
tors (two shielded), plastic jacketed
Modei515SBGX: 1.8 m (70 in.)
Models 515SBG-18X and
515SBG-18XF:
1.3 m (51 in.) from
gooseneck
Case
Silver finish die casting with black enamel diecast grille and
stainless steel screen
Dimensions
See Figure 3
1.5
in.
3.75
em
Certification
OVERALL DIMENSIONS
FIGURE 3
Conforms to European Union directives, eligible to bear CE
marking;
meets European Union EMC Immunity Requirements
(EN 55103).
Net Weight
515SBGX .... .............. ...
.................................
380 g (13.5 oz)
515SBG-18X ................................................. 900 g (31 .8 oz)
515SBG-18XF ............................................... 787 g (27.8 oz)
FURNISHED ACCESSORIES
1.27 mm (.050 in.) Hex Wrench ................................. 80A67
45.75 em (18
in.)Gooseneck
(515SBG-18X, 515SBG-18XF only)
.....
..........................
G18
Flange (515SBG-18X only) ....................................... A13HD
Flange (515SBG-18XF only) ............. ............................. A12
REPLACEMENT PARTS
Cartridge ............................................... ........................ R180
Grille Assembly ....................................................... RK334G
Cable ...................................................................... 70A4063
Gooseneck (515SBG-18X, 515SBG-18XF)
...................
G18
Flange (515SBG-18X) ............................................... A13HD
Flange (515SBG-18XF)
......................
............................ A12
Windscreen ............................................................... A85WS
CONNECTIONS
These low-impedance microphones are designed for connection to
microphone inputs rated at 75 to 300 ohms. Using balanced-line
low-impedance cables permits very long cable lengths without af-
fecting response or level. The RED and BLACK cable leads are the
microphone conductors for balanced-line connections; the shield is
connected to the amplifier ground.
For unbalanced operation, connect the BLACK lead to the shield,
and use the RED lead as the microphone conductor.
2
The GREEN and WHITE cable leads are used to control an exter-
nal relay or control circuit. Refer to the following table and to the
wiring diagram in Figure
4.
INPUT TYPE
UNBALANCED
BALANCED
RE
DOT
WIRE
FUNCTION
COLOR
RED
AUDIO
BLACK
AUDIO
GROUND
SHIELD
CHASSIS GROUND
RED
AUDIO+
BLACK
AUDIO-
SHIELD
CHASSIS GROUND
DIRECTION TO ACTUATE
SWITCH
XLR
1141N.
CONNECTOR
PHONE
PLUG
PIN2
TIP
PIN3
SLEEVE
PIN 1
SLEEVE
PIN2
TIP
PIN3
RING
PIN 1
SLEEVE
GREEN
CARTRIDGE
\j_
_
SHIELD
INTERNAL CONNECTIONS
FIGURE 4
MOUNTING THE 515SBG-18X AND 515SBG-18XF
Mount the 515SBG-18X or 515SBG-18XF as
follows:
1. Thread the supplied hexnut all the way down on the mounting
flange.
2. Thread the gooseneck tightly on the flange.
3. Back the hexnut up against the
gooseneck,
and use a wrench
to tighten the nut firmly against the bottom of the
gooseneck.
MOUNTING THE 515SBX ONTO A GOOSENECK
Mount the 515SBGX onto a gooseneck or fixed pipe with a 5/8 in-
27 thread as follows:
1. Unscrew the black end cap from the microphone.
2. Remove the thin metal washer and the metal spacer:
3. Re-install the washer by sliding it back onto the cable and up
into the end of the microphone.
4. Slip the cable into the gooseneck or pipe and thread the
microphone firmly to the mount.
For additional service or parts
information,
please contact Shure's
Service department at 1-800-516-2525. Outside the United
States,
please contact your authorized Shure Service Center.
SHURE Incorporated http://www.shure.com
United
States,
Canada,
Latin America, Caribbean:
5800 W. Touhy Avenue,
Niles,
IL
60714-4608,
U.S.A.
Phone:
847-600-2000
U.S.
Fax: 847-600-1212
Inti
Fax: 847-600-6446
Europe, Middle East, Africa:
Shure Europe
GmbH,
Phone: 49-7131-72140 Fax: 49-7131-721414
Asia, Pacific:
Shure Asia Limited, Phone: 852-2893-4290
Fax:
852-2893-4055
