Idiomas disponibles
Idiomas disponibles
Programming Setting
*There are 2 programmable back button «MR/ML» on the back of controller, each
of which can be programmed as combination of 1-20 function buttons.
Available for programming Buttons: A/B/X/Y/LB/RB/ZL/ZR/L3/ R3/ and D-pad
buttons
Programming setting steps:
1. Firstly, keep the controller under connection, simultaneously press the «Macro»
+»MR» button or «ML» button that needs to be programmed, for about 2 seconds,
the 4 signal lights LED1-LED4 flash at the same time, which means the
programming mode is turned on;
2. Then sequentially press multiple buttons you want to set
(A/B/X/Y/Z/L/ZL/ZR/L3/R3/D-pad), and the programmable button will record
the time interval of each button;
3. Lastly, press the «MR» or «ML» button once again to save the setting, the signal
lights return to continuous state, which means the programming setting of multiple
buttons is completed.
For example: keep the controller under connection, simultaneously press the
«Macro» button and «MR» button for about 2 seconds, after the four signal lights
flash at the same time, press the»B» button, then press the «A»button after 1
second, lastly press the»X» button after 3 seconds, when the setting is completed,
press «MR» button to save, and signal lights return to continuous state. The
function of MR'' button now is»B button +"A button (after 1 sec )+ «X» button
(after 3 secs).
You can test whether the setting is successful on the console via «System
Settings---Controllers and Sensors---Test Input Devices ---Test Controller Buttons»
Clear Single Back Button Programming: Enter programming mode, double -click
the corresponding Back Button to clear.
Clear All Back Button Programming: long press the « Macro» button for about 5
seconds, after the 4 signal lights flash 3 times at the same time, the clearing is
complete.
Temporarily turn on/off the back button function: double-click the «SR» button
to temporarily turn on/off the «MR» key function; double-click the «SL» button to
temporarily turn on/off the «ML» key function.
Automatic cycling on «MR» and «ML» back butotn: Press the «SR» button for
about 3 seconds, the controller vibrates once, which means the «MR» button
enters automatic cycle mode at an interval of each 3 seconds, if press the «SR»
button again for 3 seconds, the automatic cycle mode of «MR» button would be
closed;
Press the «SL» button for about 3 seconds, the controller vibrates once, which
means the «ML» button enters automatic cycle mode at an lntervaI of each 3
seconds, lfpress the «SL" button again for 3 seconds, the automatic cycle mode of
«ML» button would be closed.
Lighting Color Control
You can switch the RGB light style in cycle while press the " RGB Control Button "
when the connection with console or just charging.
Press " RGB Controller Button " long with 3-5s to power on the RGB lighting.
Vibration Adjustable Function
1.Ensure that the controller is successfully
connected to the console;
2.Press L,R,ZL, and ZR simultaneously, and
then the controller will shock once which
indicates that the adjustment is successful.
Four-level (none-weak-medium-strong) cycle
regulation is provided.
Charge Prompt
Low battery prompt: The LED5 flashes fastly. Charging: The LED5 fashes slowly.
Fully charged: The LED5 stays continuously light.
APP collaboration
The controller can work with the "Keylinker'' APP to complete some settings, the
app can change buttons function, adjust joystick control, vibration, calibrate and
upgrade the controller .
Introduction:
1. Connect the controller to the device;
2. Search for "KeyLinker" in the mobile APP store, download and install it;
3.Turn on the Bluetooth of the mobile phone and open the "Keylinker" APP;
4. Search the Bluetooth named "CND-GPW02" on the APP and click to connect.
5. After making changes as you need, click the "App" button on APP and the changes
will sync to the controller.
* Open the menu in the upper right corner of the APP interface and click " Factory
reset" or use a needle to press the "Reset" button on the back of the controller to
clear all changes on the APP and restore to the default setting.
Troubleshooting
The gamepad does not work
» Check USB connection;
» Try to plug gamepad into a different USB port;
» Restart computer/console.
» Gamepad works well when plugging into a full powered USB port. If you use USB
HUB, it must have its own power supply.
The gamepad disconnects when playing a game
» Check your console system is latest version or not, if you updated your system,
please download our updated software.
Warranty
» This product comes with 24-months limited warranty.
» For more information about usage and warranty, please refer to
www.canyon.eu/support
Manufacturer: ASBISc Enterprises PLC, Iapetou, 1, Agios Athanasios, 4101, Limassol,
Cyprus, +357 25 857000, asbis.com
According to local regulations, your product and/or its battery must be disposed of separately
from household waste. When this product has reached the end of its service life, take it to a
recycling facility designated by local authorities.
If you have any questions before returning your device to the store, please email us at support@
canyon.eu or you can chat with us at the website canyon.eu/user-help-desk.
LED indicator of strength
