Idiomas disponibles
Idiomas disponibles
EN – PRO GRABIT 4pc
Dear Customer,
Thank you for purchasing this Trend product, which
should give lasting performance if used in accordance
with these instructions.
The following symbols are used throughout this manual.
Denotes risk of personal injury, loss of life or
damage to the tool in case of non-observance of the
instructions.
Refer to the instruction manual of your power tool.
This unit must not be put into service until it has been
established that the power tool to be connected to
this unit is in compliance with 2006/42/EC (identified
by the CE marking on the power tool) or UK Statutory
Instruments 2008 No. 1597 – The Supply of Machinery
(Safety) Regulation (identified by UKCA marking on the
power tool).
SAFETY
Please read and understand the safety points in these
instructions as well as your power tool instructions.
PLEASE KEEP THESE INSTRUCTIONS
IN A SAFE PLACE
Safety Instructions
1. Disconnect power tool attachment from power
supply when not in use, before servicing, when
making adjustments and when changing accessories
such as cutters. Ensure switch is in "off" position and
cutter has stopped rotating.
2. Read and understand instructions supplied with
power tool, attachment and cutter.
3. Current Personal Protective Equipment (PPE) for eye,
ear and respiratory protection must be worn. Keep
hands, hair and clothes clear of the cutter.
4. Before each use check cutter is sharp and free
from damage. Do not use if cutter is dull, broken
or cracked or if any damage is noticeable or
suspected. Only use tools for woodworking to EN847
safety standard. Ensure cutting tool is suitable for
application.
5. The maximum speed (nmax) marked on tool or in
instructions or on packaging shall not be exceeded.
Where stated, the speed range should be adhered to.
6. Insert the shank into the router collet at least all the
way to the marked line indicated on the shank. This
ensures at least 3⁄4 of the shank length is held in
collet. Ensure clamping surfaces are clean.
7. Check all fixing and fastening nuts, bolts and screws
on power tool, attachment and cutting tools are
EN - PRO GRABIT 4pc
correctly assembled, tight and to correct torque
setting before use.
8. Ensure all visors, guards and dust extraction is fitted.
9. The direction of routing must always be opposite to
the cutter's direction of rotation.
10. Do not switch power tool on with the cutter touching
the workpiece.
11. Trial cuts should be made in waste material before
starting any project.
12. Repair of tools is only allowed according to tool
manufacturers instructions.
13. Do not take deep cuts in one pass, take shallow
passes to reduce the side load applied to the cutter.
14. User must be competent in using woodworking
equipment before using our products. Dress
properly, no loose clothing/jewellery, wear protective
hair covering for long hair.
15. Consider working environment before using
tools. Ensure working position is comfortable and
component is clamped securely. Keep proper
footing and balance at all times. Check work area for
obstructions. Keep control of power tool at all times.
16. Please keep children and visitors away from tools
and work area.
17. All tools have a residual risk so must therefore be
handled with caution.
18. Only use Trend original spare parts and accessories.
If you require further safety advice, technical information,
or spare parts, please call Trend Technical Support or
visit www.trend-uk.com
INTENDED USE
This accessory is intended to be used with a portable
power drill to remove damaged screws, machine screws
and broken bolts from wood, metal and plastic.
ITEMS REQUIRED
• Portable power drill with reverse and slow speed.
Keep a firm force down into the screw/bolt. Drill
rotation must be slow. Drill rotation must be in reverse
(anti-clockwise).
OPERATION
Damaged screw and bolt remover
• Removes cleanly from wood, metal and plastic.
• Removes screws made of any alloy including soft
brass.
• Removes free spinning screws.
-3-
