Troubleshooting - Magicvac P0116ED-1 Instrucciones De Uso

• Make sure the power cable on the MAGIC VAC
MAGIC VAC does not
®
work
• Make sure the power cable and/or plug is not defective. If so, do not use the machine.
MAGIC VAC does not
®
• Check that the piece of cut roll is correctly positioned as described in the paragraph:
perform the first seal
on the piece of cut
roll.
• In order to correctly seal the bags, the open end must be entirely inside the Vacuum
MAGIC VAC does not
®
completely vacuum-
• Make sure the Sealing Bar(6), the Airtight Gasket (7) and Sealing Gasket (9) are not dirty.
pack the bags
• The MAGIC VAC
• When you can't completely seal the bag, press the "sealing mode" button (2L) and
• If the Sealing Bar (6) overheats and melts the bag, lift the Cover (5) and allow the Sealing
MAGIC VAC does not
®
correctly seal the bag
• Check the position and integrity of the Sealing Gasket (9)
• If liquids escape during the vacuum-packing phase, remember that they must first be
• Leaks along the seal can be caused by wrinkles, crumbs, grease or liquids. Open the bag,
The MAGIC VAC bag
®
doesn't maintain its
• Make sure the bag is not punctured and thus did not maintain the vacuum. Protect any
vacuum after sealing
• Using the Canister Tube (13), connect the canister lid (or the Lid Attachment if
• Leave adequate space (at least 3 cm) between the contents and the top of the jar or
MAGIC VAC does not
®
seal containers. • Make sure that the rim of the jar or canister and universal lid are not damaged in the
• Make sure the gasket on the canister lid or universal lid is placed in the correct position
• Make sure the knob on the canister lid is set to "VACUUM" before vacuum-packing and
• Check that the O-Ring under the knob on the canister lid or universal lid is correctly
MAGIC VAC Executive
®
canisters or Universal
• Makes sure that the rim of the jar or canister and universal lid are not damaged in the
MAGIC VAC Lids do
®
• Make sure the gasket on the canister lid or universal lid is placed in the correct position
not maintain the seal
• Make sure the connection tube is correctly connected to both the canister knob as well
Make sure the knob on the lid of the Square MAGIC VAC® Executive Canister (cod.
ACO1073) is set to "OPEN - (M)" and that the Handles (1) are attached.
• Check that the O-Ring under the knob on the canister lid or universal lid is correctly
positioned.
• Makes sure that the rim of the jar or canister and universal lid are not damaged in
the sealing zone. Clean the rim and the lid with a damp cloth and reseal.
The marinating cycle
• Make sure the connection tube is correctly connected to both the canister knob as
does not start
well as the ACCESSORY PORT (3) on the machine.
correctly
• Make sure the gasket on the canister lid or universal lid is placed in the correct
position and not damaged.
• Keep the cover lightly pressed on the container when starting the first vacuum phase,

TROUBLESHOOTING

electrical outlet. Check the electrical outlet by trying another device in the same outlet.
"5 - Making bags from MAGIC VAC
Sealing Gasket
Chamber (8).
bag may be punctured. To check, seal the bag with air inside, place it
®
under water and squeeze. If you see bubbles, there is a leak. Reseal or use another bag.
increase the sealing time.
Bar (6) to cool for a few minutes.
refrigerated.
clean the upper part of the inside of the bag and remove any residue from the Sealing
Bar (6) before resealing.
pointed edges of the contents in the bag using paper napkins.
necessary) and the ACCESSORY PORT (3) on the machine.
canister.
sealing zone. Clean the rim and the lid with a damp cloth and reseal.
and not damaged.
that it is set to "CLOSED" after it is complete.
positioned.
sealing zone. Clean the rim and the lid with a damp cloth and reseal.
and not damaged.
as the ACCESSORY PORT (3) on the machine.
until the external BLUE LEDs of the Digital vacuum gauge (5) start to light up regularly.
21
is fully inserted in the machine and in the
®
rolls". Check the position and integrity of the
®