Makita DML184 Manual De Instrucciones página 5

The following table indicates the operating time on a
single charge.
Battery
Model Voltage
cartridge
BL1815
BL1815N
BL1820
18 V
BL1830
BL1840
DML184 BL1850
BL1415
BL1415N
14.4 V BL1430
BL1440
BL1450
Installing or removing the battery (Fig. 1)
• Always switch off the tool before insertion or removal of
the battery.
• To remove the battery, slide the white battery release
button down on the front of the battery and withdraw
the battery from the tool.
• To insert the battery, align the tongue on the battery
with the groove in the housing and slip it into place.
Always insert it all the way until it locks in place with a
little click. If you can see the red part on the upper side
of the button, it is not locked completely. Insert it fully
until the red part cannot be seen. If not, it may
accidentally fall out of the tool, causing injury to you or
someone around you.
• Do not use force when inserting the battery. If the battery
does not slide in easily, it is not being inserted correctly.
Switch Modes (Fig. 2)
First, depress the switch to turn on only the flourescent
lamp.
Second, if you depress the switch again, the flourescent
lamp is switched off and only the flashlight at the top turns
on.
Operating time
Fluorescent
Bulb
tube
Approx. Approx.
120 min 320 min
Approx. Approx.
150 min 400 min
Approx. Approx.
200 min 500 min
Approx. Approx.
260 min 700 min
Approx. Approx.
360 min 980 min
Approx. Approx.
470 min 1,200 min
Approx. Approx.
120 min 370 min
Approx. Approx.
150 min 450 min
Approx. Approx.
260 min 800 min
Approx. Approx.
410 min 1,260 min
Approx. Approx.
580 min 1,790 min
Third, depress the switch to turn off the flashlight.
Only
Fluorescent ON
ASSEMBLY
Replacing the Fluorescent Tube (Fig. 3)
CAUTION:
• Do not give the fluorescent tube a shock or mar it. It
may cause the glass to break and result in a serious
personal injury.
• Do not touch the fluorescent tube while it is in use or
immediately after putting out light. You may get burned.
• Always be sure that the battery is removed before replacing
the fluorescent tube or performing other maintenance.
1. Loosen the screw ring fully.
2. Pull the lamp cover straight out of the main unit.
3. Remove the cap from the fluorescent tube.
4. Pull out the fluorescent tube.
Then replace with a new Makita fluorescent tube.
Follow the procedure below to reassemble the lamp.
1. Insert the cap into the top of a new fluorescent tube.
2. Insert the lamp cover so that the slits on the lamp
cover fit into the protrusion on the tool.
3. Insert the fluorescent tube into the tool.
4. Tighten the screw ring firmly.
Replacing the Flashlight Bulb (Fig. 4, 5 & 6)
CAUTION:
• The bulb is very hot immediately after operation. Wait
until the bulb cools off before attempting to replace it.
• Always use the bulb specified only for DML184.
1. Remove the flashlight cover by turning it counterclockwise.
Then remove the reflector together with the bulb.
2. Remove the bulb holder by loosening it.
Turn the protruding part of bulb counterclockwise from
its back and remove the bulb.
3. Replace the bulb with a new one.
• Insert the new bulb into the bulb holder.
• Secure the bulb holder by screwing the bulb holder
into the reflector.
4. Tighten the flashlight cover firmly.
Strap (Fig. 7 & 8)
Install the strap on the tool by following the numbered
steps in Figure 7. (Fig. 7)
The Job Site light can hang from the strap in two basic
positions, upside down or horizontal. To hang the light in
OFF
SWITCH
MODES
Only Flashlight
ON
5