Idiomas disponibles
Idiomas disponibles
PRODUCT CHARACTERISTIC
The reflector has been designed to illuminate small open spaces: building facades, monuments, advertisements, etc. The source
of light is white LEDs, which implies low power consumption and low power losses due to the heating of the reflector. The body of
the reflector is made of aluminium. The source of light is protected with hardened glass along with a silicone gasket in the frame.
The lamp is fixed with a support, which permits to place the housing in the vertical plane at a required angle.
TECHNICAL SPECIFICATIONS
Parameter
Catalogue number
Nominal voltage
Nominal frequency
Class of electrical insulation
Grade of protection
Nominal power
Power of a single diode
Number of LEDs
Durability of the diodes
Light beam
Colour rendering index CRI Ra
Colour temperature
Power factor
Kind of power supply cable
Minimum mounting height
INSTALLATION OF THE LAMP
The installation of the reflector must be realised by a qualified electrician.
Before the installation it is required to switch off the power supply of the power network to which the reflector is to be connected! If
the recommendation is not observed, there is a risk of an electric shock which may lead to serious injuries or even death.
In case the protective glass is damaged or broken, it must be immediately replaced!
The housing must not be used without the protective glass!
Under no circumstances is it allowed to direct the beam of light to surfaces which are closer than 1 m from the glass of the lamp
or to surfaces made of inflammable materials, since it implies a risk of fire!
Installation to the surface
Reflector: YT-81800, YT-80801, YT-81803, YT-81805, YT-81806
Through the holes in the mounting holder screw the reflector to the wall or another fixed element. The holder must be fixed to the
surface in a safe and secure manner.
Make sure the lamp is fixed in accordance with the recommendations indicated in the drawing.
Reflector: YT-81801, YT-81804
The installation is to be realised as in the case of the reflector YT-81801, YT-81804, however selecting the place of installation take
into account the principle of operation of the movement sensor.
The sensor has been designed in such a manner that it functions best if it is installed approximately 3 meters from the surface. Do
not place the sensor close to trees or bushes, since they may activate the device during windy weather. Do not direct the sensor
to or place it close to sources of heat, since it also might accidentally activate the device. Do not direct the sensor towards bright
light, since the device will not function when the illumination level is set to the „moon" symbol. Do not install the sensor in places in
which there are considerable electromagnetic disturbances since it also might accidentally activate the device. The sensor is most
sensitive to movement across the detection area, in contrast to movement towards the sensor or away from the sensor. Therefore
the sensor must be placed in such a position where the movement will be perpendicular to the axis of the sensor.
Reflector: YT-81802
Put the stand base in the sleeve of the lamp base and connect the base using the knob.
Installation and replacement of the illuminating element
It is not possible to replace the illuminating element. If it is damaged, it is necessary to replace the whole reflector.
6
Unit of measurement
YT-81800
[V]
~220 - 240
[Hz]
50
I
IP65
[W]
10
[W]
10
1
[h]
[lm]
700
≥ 70
[K]
6000
0,7
[m]
3
O
P
E
R
A
T
GB
YT-81801
YT-81802
~220 - 240
~220 - 240
50
50
I
I
IP44
IP65
10
10
10
10
1
1
20 000 ± 10%
700
700
≥ 70
≥ 70
6000
6000
0,7
0,7
H05RN-F 3 x 1 mm
3
-
I
N
G
M
A
Value
YT-81803
YT-81804
~220 - 240
~220 - 240
50
50
I
I
IP65
IP44
30
30
30
30
1
1
2100
2100
≥ 95
≥ 95
6000
6000
0,95
0,95
2
3
3
N
U
A
L
YT-81806
~220 - 240
50
I
IP65
50
50
1
3500
≥ 95
6000
0,95
3
