Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
IMPORTANT:
Record the serial and key numbers from the back of the
cabinet. You will need the serial number information in
order to replace lost keys.
Do not store this document in your security cabinet.
Keep keys in a secure place away from children.
NOTE:
Assemble shelves before mounting the cabinet
to a wall or floor. Exterior access is required for
assembly. Review these instructions prior to installation.
MODEL GC-910-5
INSTALLATION OF BARREL RESTS AND SHELF
Installation of Barrel Rests
Measure and mark the locations of the barrel rests on the innner sides of the cabinet using the
dimension shown. (See figure 1)
To install the barrel rests to the cabinet, first remove the backing from the foam rests. For help in
doing this, pinch the end of the foam to help secure the adhesive to the foam.
Attach the barrel rests to the inner sides of the cabinet as shown.
Shelf Assembly
Assemble the shelf inside the cabinet with (4) 10-32 nuts and bolts as shown. (See figure 1)
Place the bottom pad (A) in the bottom of the cabinet.
CABINET MOUNTING INSTRUCTIONS
Selecting a Location
Your Security Cabinet should be installed in an isolated, dry and secure area.
For greater security the cabinet must be fastened to a solid surface with a minimum space on either side.
Ideally the cabinet would be installed on the side wall of a closet. (See figure 2)
The cabinet should be flat against the wall and floor. Remove the baseboard if necessary. (See figure 3)
Insert the plastic plugs in the cabinet's top mounting holes if you are not installing the Pistol-Ammo cabinet
on the top of the security cabinet.
Wall Mount Option
The (4) mounting holes in the rear of the cabinet must line up with the 16" centers of the wall studs. Drill
new holes in the cabinet if necessary. (See figure 3)
Drill (4) 3/16" pilot holes into the wall studs and secure the cabinet to the wall using (4 ea.) lag bolts and
washers. (See figure 3)
Floor Mount Option
The (4) mounting holes in the rear of the cabinet must line up with the 16" centers of the wall studs. Drill
new holes if necessary. (See figure 3)
Drill (2) 3/16" pilot holes into the wall studs lining up with the top (2) mounting holes in the back of the
cabinet. Secure the cabinet to the wall using (2) lag bolts and washers.
Drill (2) pilot holes and secure the cabinet bottom to the floor with (2) lag bolts and washers.
All manuals and user guides at all-guides.com
R
Home Security Cabinet
Installation Instructions
Tools Required:
Phillips screwdriver
7/16" wrench
Key #:
®
Serial #:
Drill with
3/16" bit
36"
A
1
16"
CENTERS
CABINET
TOP VIEW
2
MINIMUM
3
1
4472-0707
12
Manuales relacionados para Security Plus GC-910-5
Resumen de contenidos para Security Plus GC-910-5
- Página 1 Exterior access is required for assembly. Review these instructions prior to installation. Drill with 3/16" bit MODEL GC-910-5 36" INSTALLATION OF BARREL RESTS AND SHELF Installation of Barrel Rests Measure and mark the locations of the barrel rests on the innner sides of the cabinet using the dimension shown.
- Página 2 All manuals and user guides at all-guides.com MODEL GC-500-5 PISTOL-AMMO CABINET ASSEMBLY IMPORTANT: Install the shelf before mounting the cabinet to a wall. Install shelf with (4) 10-32 nuts and bolts. (See figure 4) Place foam pad in bottom of cabinet. Insert the plastic plugs in the cabinet's top mounting holes.
- Página 3 All manuals and user guides at all-guides.com Security Cabinets and Safes Key or Combination Request “This is not a Registration Form” Verification of ownership is required in order to receive replacement key or confirm your combination on your security product. In order to receive a replacement key or obtain the combination to your security product: Complete the following form and send to Stack-On Products.
- Página 4 This warranty extends to the initial consumer only. If you believe there is a defect in material or workmanship in your Security Plus Steel Cabinet or Pistol Box, during the one-year warranty period, please contact our customer service department, by regular mail or email at the address listed below, and include with your correspondence proof of purchase information and the model number of the product.
- Página 5 Lisez les directives avant l'installation. Perceuse et mèche de 3/16 po MODÈLE GC-910-5 36 po Installation des appuis à canon et des tablettes Installation des appuis à canon Mesurez et marquez l'emplacement des appuis à canon sur les côtés intérieurs de l'armoire selon les dimensions indiquées.
- Página 6 All manuals and user guides at all-guides.com MODÈLE GC-500-5 INSTALLATION DE L'ARMOIRE À MUNITIONS ET PISTOLETS IMPORTANT: Installez la tablette avant de fixer l'armoire au mur. Installez la tablette à l'aide de 4 boulons et écrous de 10/32. (Figure 4) Installez le revêtement en mousse au fond de l'armoire.
- Página 7 All manuals and user guides at all-guides.com Demande de clés pour les armoires de sécurité et les coffres-forts ou demande de combinaison " Ceci n'est pas un formulaire d'inscription " Il faut procéder à une vérification du contrôle de possession avant de vous envoyer une clé de remplacement ou de confirmer la combinaison de votre armoire de sécurité.
- Página 8 Cette garantie ne touche que le premier acheteur. Si vous croyez que votre armoire d’acier ou boîte à pistolets Security Plus présente un défaut de matériel ou de fabrication au cours de la période de garantie d’un an, veuillez communiquer avec notre service à...
- Página 9 Taladro con ensamblado. Lea estas instrucciones antes de instalar. una broca de 3/16" MODEO GC-910-5 36" INSTALACIÓN DE SUJETADORES PARA BARRILES Y DE LA REPISA Instalación de los Sujetadores para Barriles Mida y marque las ubicaciones de los descansos para barriles en la parte interior lateral del gabinete utilizando las dimensiones mostradas (véase la figura 1)
- Página 10 All manuals and user guides at all-guides.com MODELO GC-500-5 ENSAMBLADO DEL GABINETE PARA PISTOLAS Y MUNICIONES IMPORTANTE: Instale la repisa antes de montar el gabinete a la pared. Instale la repisa con 4 tuercas y tornillos (10-32). (véase la figura 4) Coloque el cojín de hule espuma sobre el fondo del gabinete.
- Página 11 All manuals and user guides at all-guides.com Solicitud de Llave o de Combinación para Gabinetes de Seguridad y Cajas Fuertes "Este no es un Formato de Registro" Requerimos verificación del propietario para procesar esta solicitud de llave o para confirmar la combinación de su gabinete de seguridad.
- Página 12 All manuals and user guides at all-guides.com GARANTÍA LIMITADA DE UN AÑO GABINETES DE ACERO Y CAJAS DE PISTOLAS Los Gabinetes de Acero y Cajas de Pistolas de Stack-On Products Co. (“Stack-On”) están garantizados como libres de defectos de materiales y hechura durante un período de un (1) año a partir de la fecha de compra original de un consumidor.