Visonic KP-235 PG2 Guia Del Usuario página 2

Mando 2 vías inalámbrico
Idiomas disponibles

Idiomas disponibles

3. USING THE KEYFOB
3.1 Keyfob Functionality
Step
Functions
Arm AWAY
1
Arm HOME
Disarm (OFF)
2
LATCHKEY
3
PANIC alarm
Press the
4
AUX
3.2 Keyfob Response
When executing a command, the keyfob's Transmission LED blinks red once to indicate transmission of the command to the control panel. If the
operation is successfully completed, the green LED lights momentarily and a "happy tune" is heard. If the operation fails or cannot be
completed, for example, when the system is "not ready", the red LED lights steadily and a "sad tune" is heard. When executing a command and
there is a communication failure between the keyfob device and the control panel, the keyfob's Transmission LED remains off and no tune is heard.
3.2.1 Primary LED and Buzzer Response to Keyfob Commands
Panel Response
Success: Operation is successfully completed
Fail: Operation failed
No communication: For example, control panel is out of range.
Keyfob low battery:
Note: If transmission is still possible despite the battery condition,
the unit will send a low battery signal to the control panel.
Trouble in system:
When forced arming (bypass zones) is performed, the keyfob buzzer "protests" by emitting a continuous tone during the exit delay for 5 seconds (for
more details, see the PowerMaster Installer Guide, section 5.5.2).
3.2.2 Arming LED indication
When executing a command using the keyfob device, the status of the control panel is indicated by the status LEDs that light blue.
System State
Exit from DISARM to AWAY
Exit from DISARM to HOME
Entry from HOME
Entry from AWAY
Exit from HOME TO AWAY
Exit from AWAY TO HOME
Installer mode, Sync mode or when the system is otherwise reachable but unavailable
4. MAINTENANCE
4.1 Replacing the Battery
When the keyfob device stops operating due to low battery and until the time the battery is completely depleted, all LEDs will light blue.
A replacement 3V battery, CR-2032, is available from hardware and electrical supply stores. Replace the battery as shown in Figure 2.
Caution! Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the manufacturer's instructions.
4.2 Cleaning
Clean the keyfob only with a soft cloth or sponge moistened lightly with a mixture of water and mild detergent, and wipe it dry immediately.
The use of abrasives of any kind is strictly forbidden. Also never use solvents such as kerosene, acetone or thinner.
4.3 Periodic Test
Wireless equipment should be tested regularly to determine whether there are sources of interference and to protect against faults.
Refer to the PowerMaster Installer Guide, Chapter 6 Periodic Test, for instructions on how to conduct a periodic test.
5. TROUBLESHOOTING
Problem
Keyfob does not enroll
Keyfob LED does not light when
button is pressed
2
User Actions
and
buttons simultaneously ( 2 sec.)
Diagnosis
1. Keyfob was pre-enrolled
2. The wrong ID number was entered
3. No free location
4. Unknown device
Low battery condition
D-303486 KF-235 PG2 User's Guide / Guía del usuario / Guia do utilizador
Blue LED above AWAY button lights
Blue LED above HOME button lights
Blue LED above DISARM button lights
Blue LED above AWAY button lights
-
According to the state of the alarm system, see section 2.2
Buzzer Indication
Happy (success) beep
Sad (failure) beep
None
Depends on the operation that is performed
Depends on the operation that is performed
ARM/DISARM LED Indication
AWAY lights
HOME lights
DISARM blinks
DISARM blinks
AWAY lights
HOME lights
AWAY, HOME, DISARM all blink twice, wait, then blink twice again
Proposed actions
1. Enroll the keyfob again in the vicinity of the control panel.
2. Reenter the ID number
3. If the maximum number of keyfobs has already been enrolled the
alarm system will not allow enrolling any more keyfobs.
4. Make sure the frequency used for the device is the same as the
control panel frequency.
Replace the battery
ARM/DISARM LED Indication
Transmission LED Indication
Momentary GREEN
Momentary RED
None
Blinks yellow 2 sec.
Lights yellow 2 sec.
loading