Idiomas disponibles
Idiomas disponibles
11.
When disposing the battery cartridge, remove it from
the tool and dispose of it in a safe place. Follow your
local regulations relating to disposal of battery.
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool immediately
after use as it may get hot enough to cause burns.
16. Do not allow chips, dust, or soil stuck into the
terminals, holes, and grooves of the battery
cartridge. It may result in poor performance or
breakdown of the tool or battery cartridge.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines. It may result in a malfunction or
breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
SPECIFICATIONS
This fan is equipped with 3-speed control, fan head oscillation, and auto-off timer functions. Power supply
can be with Makita battery cartridge or AC adaptor.
Model:
Rated voltage
AC adaptor
Dimensions (L x W x H)
Net weight (without battery cartridge)
•
Due to our continuing program of research and development, the specifications herein are subject to change without notice.
•
Specifications may differ from country to country.
Applicable battery cartridge and charger
Battery cartridge
Charger
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Battery running time
Following table refers to some of battery cartridges from Makita. The estimated running time of full charged battery is shown:
Battery cartridge
BL1860B
Input
Output
D.C.14.4 V Model
D.C.18 V Model
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1.
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2.
Never recharge a fully charged battery car-
tridge. Overcharging shortens the battery
service life.
3.
Charge the battery cartridge with room tem-
perature at 10 °C - 40 °C (50 °F - 104 °F). Let
a hot battery cartridge cool down before
charging it.
4.
When not using the battery cartridge, remove
it from the tool or the charger.
5.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
100 – 240 V, 50 / 60 Hz, 1.2 A max
261 mm x 439 mm x 602 mm ( 10-1/4" x 17-1/4" x 23-3/4" )
BL1815N / BL1820B / BL1830 / BL1830B / BL1840B / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / DC18SH
High
215 min
4 ENGLISH
DCF301
D.C. 14.4 V / 18 V
12 V, 3.5 A
3.8 kg (8.4 lbs)
BL1430B
Wind speed
Medium
430 min
Low
850 min
