Broan QTR080L Instrucciones
Ocultar thumbs Ver también para QTR080L:
Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

QTR / QTRE SERIES
FAN / LIGHT / NIGHT LIGHTS
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-
JURY TO PERSONS, OBSERVE THE FOLLOWING:
1. Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer at the address
or telephone number listed in the warranty.
2. Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by a quali-
fied person(s) in accordance with all applicable codes and stan-
dards, including fire-rated construction codes and standards.
4. Sufficient air is needed for proper combustion and exhausting
of gases through the flue (chimney) of fuel burning equipment
to prevent backdrafting. Follow the heating equipment
manufacturer's guideline and safety standards such as those
published by the National Fire Protection Association (NFPA),
and the American Society for Heating, Refrigeration and Air
Conditioning Engineers (ASHRAE), and the local code au-
thorities.
5. When cutting or drilling into wall or ceiling, do not damage
electrical wiring and other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. Acceptable for use over a tub or shower when connected to a
GFCI (Ground Fault Circuit Interrupter) - protected branch cir-
cuit.
8. This unit must be grounded.
!
CAUTION
1. For general ventilating use only. Do not use to exhaust haz-
ardous or explosive materials and vapors.
2. This product is designed for installation in ceilings up to a 7/12
pitch (Models QTR080L and QTR110L) or a 12/12 pitch (Mod-
els QTRE080FLT and QTRE110FLT). Duct connector must
point up. DO NOT MOUNT THIS PRODUCT IN A WALL.
3. To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction dust, etc. off power
unit.
4. Please read specification label on product for further informa-
tion and requirements.
Installer: Leave this manual with the homeowner.
MODELS QTR080L • QTRE080FLT •
CLEANING & MAINTENANCE
For quiet and efficient operation, long life, and attractive appear-
ance - lower or remove grille and vacuum interior of unit with the
dusting brush attachment.
The motor is permanently lubricated and never needs oiling. If
the motor bearings are making excessive or unusual noises,
replace the motor with the exact service motor. The impeller should
also be replaced.
OPERATION
The fan, light, and night light can be operated separately. Use a
3-function wall control. Do not use a dimmer switch to operate
the light (Models QTRE080FLT and QTRE110FLT only). See
"Connect Wiring" for details.
WARRANTY
BROAN THREE YEAR LIMITED WARRANTY
Broan warrants to the original consumer purchaser of its products that
such products will be free from defects in materials or workmanship for a
period of three years from the date of original purchase. THERE ARE NO
OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT
LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR FIT-
NESS FOR A PARTICULAR PURPOSE.
During this three-year period, Broan will, at its option, repair or replace,
without charge, any product or part which is found to be defective under
normal use and service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP
STARTERS AND TUBES. This warranty does not cover (a) normal main-
tenance and service or (b) any products or parts which have been subject
to misuse, negligence, accident, improper maintenance or repair (other
than by Broan), faulty installation or installation contrary to recommended
installation instructions.
The duration of an implied warranty is limited to the three-year period as
specified for the express warranty. Some states do not allow limitation on
how long an implied warranty lasts, so the above limitation may not apply
to you.
BROAN'S OBLIGATION TO REPAIR OR REPLACE, AT BROAN'S OP-
TION, SHALL BE THE PURCHASER'S SOLE AND EXCLUSIVE REM-
EDY UNDER THIS WARRANTY. BROAN SHALL NOT BE LIABLE FOR
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT
OF OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE.
Some states do not allow the exclusion or limitation of incidental or conse-
quential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other
rights, which vary from state to state. This warranty supersedes all prior
warranties.
To qualify for warranty service, you must (a) notify Broan at the address or
telephone number stated below, (b) give the model number and part iden-
tification and (c) describe the nature of any defect in the product or part. At
the time of requesting warranty service, you must present evidence of the
original purchase date.
Broan-NuTone LLC, 926 West State Street, Hartford, WI 53027
(1-800-637-1453)
QTR110L • QTRE110FLT
Page 1
loading

Resumen de contenidos para Broan QTR080L

  • Página 1 3. To avoid motor bearing damage and noisy and/or unbalanced To qualify for warranty service, you must (a) notify Broan at the address or impellers, keep drywall spray, construction dust, etc. off power telephone number stated below, (b) give the model number and part iden- tification and (c) describe the nature of any defect in the product or part.
  • Página 2 MODELS QTR080L • QTRE080FLT • QTR110L • QTRE110FLT Page 2 TYPICAL INSTALLATIONS PLAN THE INSTALLATION ROOF CAP 4-IN. ROUND DUCT Housing mounted to I-joists. WALL 4-IN. ROUND Use I-joist spacer block (provided). Purchase ELBOW separately The unit will operate most quietly and efficiently when located where the shortest possible duct run and minimum number of elbows will be needed.
  • Página 3 MODELS QTR080L • QTRE080FLT • QTR110L • QTRE110FLT Page 3 INSTALL HOUSING & DUCT CONNECT WIRING 1. Bend housing tabs. Use a pliers to bend housing TABS out to 90 TABS 2. Mount SPACER (use for mounting to I-Joist) housing to joist.
  • Página 4 MODELS QTR080L • QTRE080FLT • QTR110L • QTRE110FLT Page 4 8. Push grille against ceiling. 9. Remove light lens. Carefully insert a small flat-blade screwdriver betweeen grille SERVICE NOTE and lens. Pry To remove Blower Assembly: lens out. Unplug motor (7).
  • Página 5 NO MONTE ESTE PRODUCTO EN UNA TECHO. Para tener derecho al servicio de la garantía, usted debe (a) notificar a Broan 3. Para evitar daños a los cojinetes del motor y rotores ruidosos y/o no NuTone a la dirección y número de teléfono que aparecen abajo, (b) proporcio- equilibrados, mantenga la unidad de accionamiento al resguardo de nar el número de modelo y la identificación de la pieza y (c) describir la natura-...
  • Página 6 MODELOS QTR080L • QTRE080FLT • QTR110L • QTRE110FLT Página 6 INSTALACIONES TÍPICAS PLANIFICACIÓN DE LA INSTALACIÓN TAPA DE TECHO * CONDUCTO REDONDO DE 4 PULG. * Montaje de la cubierta en viguetas "I". Utilice un taco separador de viguetas "I"...
  • Página 7 MODELOS QTR080L • QTRE080FLT • QTR110L • QTRE110FLT Página 7 INSTALE LA CUBIERTA CONEXIÓN ELÉCTRICA Y EL CONDUCTO 1. Doble las lengüetas de la cubierta. Con un alicate, doble las LENGÜETAS LENGÜETAS de la cubierta a 90°. 2. Monte la...
  • Página 8 MODELOS QTR080L • QTRE080FLT • QTR110L • QTRE110FLT Página 8 8. Empuje la rejilla contra el cielo raso. 9. Saque la NOTA DE SERVICIO lente de la Para desmontar el conjunto lámpara. del ventilador: Con cuidado, inserte Desenchufe el motor (7).

Este manual también es adecuado para:

Qtre serieQtre080ftlQtre110ftlQtr serieQtr110l