Idiomas disponibles
Idiomas disponibles
6. STARTING UP THE MACHINE
To start the machine, press button A forward (Fig. 1) to
the on position. To stop the machine, simply press the
back of the switch and it will return to the off position.
The electronic control enables you to work at the ideal
speed for each type of job and bit. Adjust the speed
using button I (Fig. 2).
7. MAINTENANCE BRUSHES AND COLLECTOR
Disconnect the machine from the mains
before carrying out any kind of mainte-
nance work.
Remove screws D (Fig. 4) that fasten the side covers E
and detach both.
Remove the brush-holder G (Fig. 5) with small screw-
driver F, using one of the brush-holder side tabs to
lever it out.
Push back the end of spring H. Keep it in this position
to extract the brush and replace it with a new genuine
Virutex brush. Reinsert the brush-holder, ensuring
that it is firmly positioned in the casing and that each
of the brushes exerts a small amount of pressure on
the collector.
Re-attach the covers E with the corresponding screws,
making sure that no wires get caught in the process. It
is advisable to leave the machine running for 15 minutes
once the brushes have been changed. If the collector
burns or juts out, it should be serviced by a Virutex
service technician.
Keep the lead and plug in good working condition.
8. ACCESSORIES
1222084 – Ø 6 mm collet
1222024 – Ø 8 mm collet
1222085 – Ø 6.35 mm (1/4") collet
9. NOISE LEVEL AND VIBRATIONS
The noise and vibration levels of this device have been
measured in accordance with European standard EN
60745-2-3 and EN 60745-1 and serve as a basis for com-
parison with other machines with similar applications.
The indicated vibration level has been determined for
the device's main applications and may be used as an
initial value for evaluating the risk presented by expo-
sure to vibrations. However, vibrations may reach levels
that are quite different from the declared value under
other application conditions, with other tools or with
insufficient maintenance of the electrical device or its
accessories, reaching a much higher value as a result
of the work cycle or the manner in which the electrical
device is used.
6
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations, such
as maintaining both the device and its tools in perfect
condition and organising the duration of work cycles
(such as operating times when the machine is subjected
to loads, and operating times when working with no-load,
in effect, not in use, as reducing the latter may have a
considerable effect upon the overall exposure value).
10. GUARANTEE
All VIRUTEX power tools have a guarantee which is
valid for 12 months from the date of purchase. Damage
caused by inadequate handling or natural wear and tear
is excluded. For any repairs, contact the official VIRUTEX
technical service centre.
VIRUTEX reserves the right to modify its products
without prior notice.
F R A N Ç A I S
MEULEUSE DROITE R0156N
Important
Avant d'utiliser la machine, lisez attenti-
vement ce MANUEL D'INSTRUCTIONS et la
BROCHURE D'INSTRUCTIONS GÉNÉRALES
DE SÉCURITÉ qui vous sont fournis avec
cette machine. Assurez-vous de bien
avoir tout compris avant de commencer
à travailler sur la machine.
Gardez toujours ces deux manuels d'instructions à
portée de la main pour pouvoir les consulter, en cas
de besoin.
1. INSTRUCTIONS DE SÉCURITÉ POUR
LE MANIEMENT DE LA MEULEUSE DROITE
Veuillez lire attentivement la BROCHURE
D'INSTRUCTIONS GÉNÉRALES DE SÉCU-
RITÉ qui est jointe à la documentation
de la machine.
1. Avant de brancher la machine, vérifier si la tension
d'alimentation correspond à celle indiquée sur la plaque
des caractéristiques.
2. Toujours maintenir les mains éloignées de la zone de
coupe. Toujours fixer fermement la machine.
3. Utiliser toujours des outils d'origine VIRUTEX. Ne jamais
